Re: [PATCH] net: phy: at803x: Improve hibernation support on start up

From
Russell King (Oracle) <linux@armlinux.org.uk>
Date
2023-08-10 10:30:17
Also in
linux-clk
Reply to
Russell King (Oracle), 2023-08-09
On Wed, Aug 09, 2023 at 09:43:49AM +0100, Russell King (Oracle) wrote:
On Wed, Aug 09, 2023 at 08:08:36AM +0200, Oleksij Rempel wrote:
quoted
If fully functional external clock provider is need to initialize the
MAC, just disabling this clock on already initialized HW without doing
proper re-initialization sequence is usually bad idea. HW may get some
glitch which will make troubleshooting a pain.
There are cases where the PHY sits on a MDIO bus that is created
by the ethernet MAC driver, which means the PHY only exists during
the ethernet MAC driver probe.

I think that provided the clock is only obtained after we know the
PHY is present, that would probably be fine - but doing it before
the MDIO bus has been created will of course cause problems.

We've had these issues before with stmmac, so this "stmmac needs the
PHY receive clock" is nothing new - it's had problems with system
suspend/resume in the past, and I've made suggestions... and when
there's been two people trying to work on it, I've attempted to get
them to talk to each other which resulted in nothing further
happening.

Another solution could possibly be that we reserve bit 30 on the
PHY dev_flags to indicate that the receive clock must always be
provided. I suspect that would have an advantage in another
situation - for EEE, there's a control bit which allows the
receive clock to be stopped while the link is in low-power state.
If the MAC always needs the receive clock, then obviously that
should be blocked.
Something like this for starters:
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index fcab363d8dfa..a954f1d61709 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1254,6 +1254,11 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 			~(MAC_10HD | MAC_100HD | MAC_1000HD);
 	priv->phylink_config.mac_managed_pm = true;
 
+	/* stmmac always requires a receive clock in order for things like
+	 * hardware reset to work.
+	 */
+	priv->phylink_config.mac_requires_rxc = true;
+
 	phylink = phylink_create(&priv->phylink_config, fwnode,
 				 mode, &stmmac_phylink_mac_ops);
 	if (IS_ERR(phylink))
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 13c4121fa309..619a63a0d14f 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -990,7 +990,8 @@ static int at803x_hibernation_mode_config(struct phy_device *phydev)
 	/* The default after hardware reset is hibernation mode enabled. After
 	 * software reset, the value is retained.
 	 */
-	if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE))
+	if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE) &&
+	    !(phydev->dev_flags & PHY_F_RXC_ALWAYS_ON))
 		return 0;
 
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 3e9909b30938..4d1a37487923 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -3216,6 +3216,8 @@ static int phy_probe(struct device *dev)
 			goto out;
 	}
 
+        phy_disable_interrupts(phydev);
+
 	/* Start out supporting everything. Eventually,
 	 * a controller will attach, and may modify one
 	 * or both of these values
@@ -3333,16 +3335,6 @@ static int phy_remove(struct device *dev)
 	return 0;
 }
 
-static void phy_shutdown(struct device *dev)
-{
-	struct phy_device *phydev = to_phy_device(dev);
-
-	if (phydev->state == PHY_READY || !phydev->attached_dev)
-		return;
-
-	phy_disable_interrupts(phydev);
-}
-
 /**
  * phy_driver_register - register a phy_driver with the PHY layer
  * @new_driver: new phy_driver to register
@@ -3376,7 +3368,6 @@ int phy_driver_register(struct phy_driver *new_driver, struct module *owner)
 	new_driver->mdiodrv.driver.bus = &mdio_bus_type;
 	new_driver->mdiodrv.driver.probe = phy_probe;
 	new_driver->mdiodrv.driver.remove = phy_remove;
-	new_driver->mdiodrv.driver.shutdown = phy_shutdown;
 	new_driver->mdiodrv.driver.owner = owner;
 	new_driver->mdiodrv.driver.probe_type = PROBE_FORCE_SYNCHRONOUS;
 
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 4f1c8bb199e9..6568a2759101 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1830,6 +1830,8 @@ static int phylink_bringup_phy(struct phylink *pl, struct phy_device *phy,
 static int phylink_attach_phy(struct phylink *pl, struct phy_device *phy,
 			      phy_interface_t interface)
 {
+	u32 flags = 0;
+
 	if (WARN_ON(pl->cfg_link_an_mode == MLO_AN_FIXED ||
 		    (pl->cfg_link_an_mode == MLO_AN_INBAND &&
 		     phy_interface_mode_is_8023z(interface) && !pl->sfp_bus)))
@@ -1838,7 +1840,10 @@ static int phylink_attach_phy(struct phylink *pl, struct phy_device *phy,
 	if (pl->phydev)
 		return -EBUSY;
 
-	return phy_attach_direct(pl->netdev, phy, 0, interface);
+	if (pl->config.mac_requires_rxc)
+		flags |= PHY_F_RXC_ALWAYS_ON;
+
+	return phy_attach_direct(pl->netdev, phy, flags, interface);
 }
 
 /**
@@ -1941,6 +1946,9 @@ int phylink_fwnode_phy_connect(struct phylink *pl,
 		pl->link_config.interface = pl->link_interface;
 	}
 
+	if (pl->config.mac_requires_rxc)
+		flags |= PHY_F_RXC_ALWAYS_ON;
+
 	ret = phy_attach_direct(pl->netdev, phy_dev, flags,
 				pl->link_interface);
 	phy_device_free(phy_dev);
diff --git a/include/linux/phy.h b/include/linux/phy.h
index ba08b0e60279..79df5e01707d 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -761,6 +761,7 @@ struct phy_device {
 
 /* Generic phy_device::dev_flags */
 #define PHY_F_NO_IRQ		0x80000000
+#define PHY_F_RXC_ALWAYS_ON	BIT(30)
 
 static inline struct phy_device *to_phy_device(const struct device *dev)
 {
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 789c516c6b4a..a83c1a77338f 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -204,6 +204,7 @@ enum phylink_op_type {
  * @poll_fixed_state: if true, starts link_poll,
  *		      if MAC link is at %MLO_AN_FIXED mode.
  * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM.
+ * @mac_requires_rxc: if true, the MAC always requires a receive clock from PHY.
  * @ovr_an_inband: if true, override PCS to MLO_AN_INBAND
  * @get_fixed_state: callback to execute to determine the fixed link state,
  *		     if MAC link is at %MLO_AN_FIXED mode.
@@ -216,6 +217,7 @@ struct phylink_config {
 	enum phylink_op_type type;
 	bool poll_fixed_state;
 	bool mac_managed_pm;
+	bool mac_requires_rxc;
 	bool ovr_an_inband;
 	void (*get_fixed_state)(struct phylink_config *config,
 				struct phylink_link_state *state);
-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Thread (32 messages) 32 messages, 6 authors, last reply 2023-12-15
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help