Re: [PATCH 10/10] ravb: Initialize GbEthernet E-MAC

On 10/4/21 10:23 PM, Biju Das wrote:

[...]

quoted

quoted

Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with the
naming convention used in sh_eth driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
RFC->v1:
 * Moved CSR0 intialization to later patch.
 * started using ravb_modify for initializing link registers.
---
 drivers/net/ethernet/renesas/ravb.h      | 20 +++++++--
 drivers/net/ethernet/renesas/ravb_main.c | 55
++++++++++++++++++++----
 2 files changed, 62 insertions(+), 13 deletions(-)

[...]

quoted

quoted

diff --git a/drivers/net/ethernet/renesas/ravb_main.c

b/drivers/net/ethernet/renesas/ravb_main.c
index 3e694738e683..9a4888543384 100644

--- a/drivers/net/ethernet/renesas/ravb_main.c
+++ b/drivers/net/ethernet/renesas/ravb_main.c

[...]

quoted

@@ -449,10 +461,35 @@ static int ravb_ring_init(struct net_device

*ndev, int q)

 static void ravb_emac_init_gbeth(struct net_device *ndev)  {
-	/* Place holder */
+	struct ravb_private *priv = netdev_priv(ndev);
+
+	/* Receive frame limit set register */
+	ravb_write(ndev, GBETH_RX_BUFF_MAX + ETH_FCS_LEN, RFLR);
+
+	/* PAUSE prohibition */

    Should be:

	/* EMAC Mode: PAUSE prohibition; Duplex; TX; RX */

quoted

+	ravb_write(ndev, ECMR_ZPF | ((priv->duplex > 0) ? ECMR_DM : 0) |
+			 ECMR_TE | ECMR_RE | ECMR_RCPT |
+			 ECMR_TXF | ECMR_RXF | ECMR_PRM, ECMR);
+
+	ravb_set_rate_gbeth(ndev);
+
+	/* Set MAC address */
+	ravb_write(ndev,
+		   (ndev->dev_addr[0] << 24) | (ndev->dev_addr[1] << 16) |
+		   (ndev->dev_addr[2] << 8)  | (ndev->dev_addr[3]), MAHR);
+	ravb_write(ndev, (ndev->dev_addr[4] << 8)  | (ndev->dev_addr[5]),
+MALR);
+
+	/* E-MAC status register clear */
+	ravb_write(ndev, ECSR_ICD | ECSR_LCHNG | ECSR_PFRI, ECSR);
+
+	/* E-MAC interrupt enable register */
+	ravb_write(ndev, ECSIPR_ICDIP, ECSIPR);

   Too much repetitive code, I think...

Can you please clarify what are the codes repetitive here?

   MAHR/MALR reading, mainly...
   The following code turned out to be different from gen2/3 indeed...

[...]

MBR, Sergey