Re: [RFC net-next PATCH 16/16] net: sfp: Add quirk to ignore PHYs
From: "Russell King (Oracle)" <linux@armlinux.org.uk>
Date: 2021-10-05 22:17:19
Also in:
lkml
On Tue, Oct 05, 2021 at 04:38:23PM -0400, Sean Anderson wrote:
There is a level shifter. Between the shifter and the SoC there were 1.8k (!) pull-ups, and between the shifter and the SFP there were 10k pull-ups. I tried replacing the pull-ups between the SoC and the shifter with 10k pull-ups, but noticed no difference. I have also noticed no issues accessing the EEPROM, and I have not noticed any difference accessing other registers (see below). Additionally, this same error is "present" already in xgbe_phy_finisar_phy_quirks(), as noted in the commit message.
Hmm, thanks for checking. So it's something "weird" that this module is doing. As I say, the 88E1111 has a native I2C mode, it sounds like they're not using it but have their own, seemingly broken, protocol conversion from the I2C bus to MDIO. I've opened and traced the I2C connections on this module - they only go to an EEPROM and the 88E1111, so we know this is a "genuine" 88E1111 in I2C mode we are talking to.
First, reading two bytes at a time $ i2ctransfer -y 2 w1@0x56 2 r2 0x01 0xff This behavior is repeatable $ i2ctransfer -y 2 w1@0x56 2 r2 0x01 0xff Now, reading one byte at a time $ i2ctransfer -y 2 w1@0x56 2 r1 0x01 A second write/single read gets us the first byte again. $ i2ctransfer -y 2 w1@0x56 2 r1 0x41
I think you mean you get the other half of the first word. When I try this with a 88E1111 directly connected to the I2C bus, I get: root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r2 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r2 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r1 0x01 root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r1 0x01 So a completely different behaviour. Continuing...
And doing it for a third time gets us the first byte again. $ i2ctransfer -y 2 w1@0x56 2 r1 0x01 If we start another one-byte read without writing the address, we get the second byte $ i2ctransfer -y 2 r1@0x56 0x41
root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r1 0x01 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 Again, different behaviour.
And continuing this pattern, we get the next byte. $ i2ctransfer -y 2 r1@0x56 0x0c This can be repeated indefinitely $ i2ctransfer -y 2 r1@0x56 0xc2 $ i2ctransfer -y 2 r1@0x56 0x0c
root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x41 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 Here we eventually start toggling between the high and low bytes of the word.
But stopping in the "middle" of a register fails $ i2ctransfer -y 2 w1@0x56 2 r1 Error: Sending messages failed: Input/output error
root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 r1 0x01 No error for me.
We don't have to immediately read a byte: $ i2ctransfer -y 2 w1@0x56 2 $ i2ctransfer -y 2 r1@0x56 0x01 $ i2ctransfer -y 2 r1@0x56 0x41
root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 Again, no toggling between high/low bytes of the word.
We can read two bytes indefinitely after "priming the pump" $ i2ctransfer -y 2 w1@0x56 2 r1 0x01 $ i2ctransfer -y 2 r1@0x56 0x41 $ i2ctransfer -y 2 r2@0x56 0x0c 0xc2 $ i2ctransfer -y 2 r2@0x56 0x0c 0x01 $ i2ctransfer -y 2 r2@0x56 0x00 0x00 $ i2ctransfer -y 2 r2@0x56 0x00 0x04 $ i2ctransfer -y 2 r2@0x56 0x20 0x01 $ i2ctransfer -y 2 r2@0x56 0x00 0x00
root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 root@clearfog21:~# i2ctransfer -y 1 r2@0x56 0x01 0x41 No auto-increment of the register.
But more than that "runs out" $ i2ctransfer -y 2 w1@0x56 2 r1 0x01 $ i2ctransfer -y 2 r1@0x56 0x41 $ i2ctransfer -y 2 r4@0x56 0x0c 0xc2 0x0c 0x01 $ i2ctransfer -y 2 r4@0x56 0x00 0x00 0x00 0x04 $ i2ctransfer -y 2 r4@0x56 0x20 0x01 0xff 0xff $ i2ctransfer -y 2 r4@0x56 0x01 0xff 0xff 0xff
root@clearfog21:~# i2ctransfer -y 1 w1@0x56 2 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r1@0x56 0x01 root@clearfog21:~# i2ctransfer -y 1 r4@0x56 0x01 0x41 0x0c 0xc2 root@clearfog21:~# i2ctransfer -y 1 r4@0x56 0x01 0x41 0x0c 0xc2 root@clearfog21:~# i2ctransfer -y 1 r4@0x56 0x01 0x41 0x0c 0xc2 root@clearfog21:~# i2ctransfer -y 1 r4@0x56 0x01 0x41 0x0c 0xc2
However, the above multi-byte reads only works when starting at register 2 or greater. $ i2ctransfer -y 2 w1@0x56 0 r1 0x01 $ i2ctransfer -y 2 r1@0x56 0x40 $ i2ctransfer -y 2 r2@0x56 0x01 0xff Based on the above session, I believe that it may be best to treat this phy as having an autoincrementing register address which must be read one byte at a time, in multiples of two bytes. I think that existing SFP phys may compatible with this, but unfortunately I do not have any on hand to test with.
Sadly, according to my results above, I think your module is doing something strange with the 88E1111. You say that it's Finisar, but I can only find this module in Fiberstore's website: https://www.fs.com/uk/products/20057.html Fiberstore commonly use "FS" in the vendor field. You have me wondering what they've done to this PHY to make it respond in the way you are seeing. -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!