Hi Marcel.

Marcel Holtmann wrote:

quoted

+/**
+ * struct sockaddr_caif - the sockaddr structure for CAIF sockets.
+ * @u:			     Union of address data 'switched' by familty.
+ * @at:			     Applies when family = CAIFPROTO_AT.
+ * @at.type:		     Type of AT link to set up (enum caif_at_type).
+ * @util:		     Applies when family = CAIFPROTO_UTIL
+ * @util.service:	     Service name.
+ * @dgm:		     Applies when family = CAIFPROTO_DATAGRAM
+ * @dgm.connection_id:	     Datagram connection id.
+ * @dgm.nsapi:		     NSAPI of the PDP-Context.
+ * @rfm:		     Applies when family = CAIFPROTO_RFM
+ * @rfm.connection_id:       Connection ID for RFM.
+ * @rfm.volume:	     	     Volume to mount.
+ */
+struct sockaddr_caif {
+	sa_family_t  family;
+	union {
+		struct {
+			u_int8_t  type;		/* type: enum caif_at_type */
+		} at;				/* CAIFPROTO_AT */
+		struct {
+			char	  service[16];
+		} util;				/* CAIFPROTO_UTIL */
+		union {
+			u_int32_t connection_id;
+			u_int8_t  nsapi;
+		} dgm;				/* CAIFPROTO_DATAGRAM(_LOOP)*/
+		struct {
+			u_int32_t connection_id;
+			char	  volume[16];
+		} rfm;				/* CAIFPROTO_RFM */
+	} u;
+};

as mentioned on the oFono mailing list, what is the right procedure
to select a local CAIF device for usage with doing bing(). The use
case I am thinking of is that you have multiple CAIF device attached
to the same system. Think of desktops with USB or even Dual-SIM
phones. Before we set the API in stone, we need to have a way o bind
the socket to a specific device. Maybe it is possible, but I am
missing it.      

The CAIF interface can be selected by using the following types:
[snip caif_config.h]
/**
 * enum caif_phy_preference  - Types of physical HW interfaces
 *				       towards modem defined in CAIF stack
 * @CAIF_PHYPREF_UNSPECIFIED:	Default physical interface
 * @CAIF_PHYPREF_LOW_LAT:	Default physical interface for low-latency
 *				      traffic
 * @CAIF_PHYPREF_HIGH_BW:	Default physical interface for high-bandwidth
 *				      traffic
 * @CAIF_PHYPREF_LOOP:		TEST Loopback interface, simulating modem
 *				      responses
 *
 * For client convenience, two special types are defined:
 * CAIF_PHYPREF_LOW_LAT is the preferred low-latency physical link.
 * Typically used for "control" purposes.
 * CAIF_PHYPREF_HIGH_BW is the preferred high-bandwidth physical link.
 * Typically used for "payload" purposes.
 */
...
enum caif_phy_preference {
	CAIF_PHYPREF_UNSPECIFIED,
	CAIF_PHYPREF_LOW_LAT,
	CAIF_PHYPREF_HIGH_BW,
	CAIF_PHYPREF_LOOP
};
[snip caif_socket.h]
...
/**
 * struct caif_channel_opt - CAIF channel connect options.
 * @priority:		Priority of the channel (between 0 and 0x1f)
 * @link_selector:	Selector for the physical link.
 *			      (see enum caif_phy_preference in caif_config.h)
 * @link_name:		Physical link to use. This is the instance name of the
 *			      CAIF Physical Driver.
 */
struct caif_channel_opt {
	u_int16_t  priority;
	u_int16_t  link_selector;
	char	   link_name[16];
};
...
/** enum caif_socket_opts - CAIF option values for getsockopt and setsockopt
 * @CAIFSO_CHANNEL:		Used to set the connect options on a CAIF
 *				socket. (struct caif_config_opt). This can only
 *				be set before connecting.
[end snip]

CAIFSO_CHANNEL is used for specifying the physical interface to use for the 
CAIF Channel. You can select the type of interface to use
by setting link_selector:
CAIF_PHYPREF_LOW_LAT will typically be used for AT (or other control traffic),
and CAIF_PHYPREF_HIGH_BW for IP traffic.
When the CAIF interfaces registers itself it will inform about their type,
(low-latency or high-bandwidth). This approach assumes that you have only one
modem, but multiple links to it (e.g. USB and UART). 

But you can also specify interface by name using link_name. In this case
you specify the name of the interface to use. I think this would support
your use case with multiple modems attached.

BR/Sjur