在 2024/7/2 16:28, Serge Semin 写道:

On Wed, May 29, 2024 at 06:19:03PM +0800, Yanteng Si wrote:

quoted

Loongson delivers two types of the network devices: Loongson GMAC and
Loongson GNET in the framework of four CPU/Chipsets revisions:

    Chip             Network  PCI Dev ID   Synopys Version   DMA-channel
LS2K1000 CPU         GMAC      0x7a03       v3.50a/v3.73a        1
LS7A1000 Chipset     GMAC      0x7a03       v3.50a/v3.73a        1
LS2K2000 CPU         GNET      0x7a13          v3.73a            8
LS7A2000 Chipset     GNET      0x7a13          v3.73a            1

The driver currently supports the chips with the Loongson GMAC network
device. As a preparation before adding the Loongson GNET support
detach the Loongson GMAC-specific platform data initializations to the
loongson_gmac_data() method and preserve the common settings in the
loongson_default_data().

While at it drop the return value statement from the
loongson_default_data() method as redundant.

Based on the last hardware setup insight Loongson GMAC with AV-feature
can be found on the LS2K2000 CPU. Thus the commit log should be:

"Loongson delivers two types of the network devices: Loongson GMAC and
Loongson GNET in the framework of four CPU/Chipsets revisions:

    Chip             Network  PCI Dev ID   Synopys Version   DMA-channel
LS2K1000 CPU         GMAC      0x7a03       v3.50a/v3.73a        1
LS7A1000 Chipset     GMAC      0x7a03       v3.50a/v3.73a        1
LS2K2000 CPU         GMAC      0x7a03          v3.73a            8
LS2K2000 CPU         GNET      0x7a13          v3.73a            8
LS7A2000 Chipset     GNET      0x7a13          v3.73a            1

The driver currently supports the chips with the Loongson GMAC network
device synthesized with a single DMA-channel available. As a
preparation before adding the Loongson GNET support detach the
Loongson GMAC-specific platform data initializations to the
loongson_gmac_data() method and preserve the common settings in the
loongson_default_data().

While at it drop the return value statement from the
loongson_default_data() method as redundant."

OK, Thank you very much!

quoted

Signed-off-by: Feiyang Chen <redacted>
Signed-off-by: Yinggang Gu <redacted>
Signed-off-by: Yanteng Si <redacted>
---
  .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 19 ++++++++++++-------
  1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
index 739b73f4fc35..ad3f44440963 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c

@@ -11,7 +11,7 @@
  
  #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
  
-static int loongson_default_data(struct plat_stmmacenet_data *plat)
+static void loongson_default_data(struct plat_stmmacenet_data *plat)
  {
  	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
  	plat->has_gmac = 1;

@@ -20,16 +20,14 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
  	/* Set default value for multicast hash bins */
  	plat->multicast_filter_bins = 256;
  
+	plat->mac_interface = PHY_INTERFACE_MODE_NA;
+
  	/* Set default value for unicast filter entries */
  	plat->unicast_filter_entries = 1;
  
  	/* Set the maxmtu to a default of JUMBO_LEN */
  	plat->maxmtu = JUMBO_LEN;
  
-	/* Set default number of RX and TX queues to use */
-	plat->tx_queues_to_use = 1;
-	plat->rx_queues_to_use = 1;
-
  	/* Disable Priority config by default */
  	plat->tx_queues_cfg[0].use_prio = false;
  	plat->rx_queues_cfg[0].use_prio = false;

@@ -42,6 +40,11 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
  
  	plat->dma_cfg->pbl = 32;
  	plat->dma_cfg->pblx8 = true;
+}
+
+static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
+{
+	loongson_default_data(plat);
  
  	return 0;
  }

@@ -111,11 +114,10 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
  	}
  
  	plat->phy_interface = phy_mode;
-	plat->mac_interface = PHY_INTERFACE_MODE_GMII;
  
  	pci_set_master(pdev);
  
-	loongson_default_data(plat);
+	loongson_gmac_data(plat);
  	pci_enable_msi(pdev);
  	memset(&res, 0, sizeof(res));
  	res.addr = pcim_iomap_table(pdev)[0];

@@ -140,6 +142,9 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
  		goto err_disable_msi;
  	}
  
+	plat->tx_queues_to_use = 1;
+	plat->rx_queues_to_use = 1;
+

Please move this to the loongson_gmac_data(). Thus all the
platform-data initializations would be collected in two coherent
methods: loongson_default_data() and loongson_gmac_data(). It will be
positive from the readability and maintainability points of view.

OK, I will move this to the  loongson_default_data(),

Because loongson_gmac/gnet_data() call it.

In the patch adding the Loongson multi-channel GMAC support make sure
the loongson_data::loongson_id field is initialized before the
stmmac_pci_info::setup() method is called.

I've tried. It's almost impossible.


The only way to do this is to initialize loongson_id again in 
loongson_default_data().

But that will add a lot of code.


Hmm, how about:


loongson_default_data() {

     plat->tx_queues_to_use = 1;
     plat->rx_queues_to_use = 1;

     ...

}


loongson_dwmac_probe() {

     ...

     if (ld->loongson_id == DWMAC_CORE_LS2K2000) {
         plat->rx_queues_to_use = CHANNEL_NUM;
         plat->tx_queues_to_use = CHANNEL_NUM;

         /* Only channel 0 supports checksum,
          * so turn off checksum to enable multiple channels.
          */
         for (i = 1; i < CHANNEL_NUM; i++)
             plat->tx_queues_cfg[i].coe_unsupported = 1;

         ret = loongson_dwmac_msi_config(pdev, plat, &res);
     } else {
         ret = loongson_dwmac_intx_config(pdev, plat, &res);
     }

     ...

}



Thanks,

Yanteng

-Serge(y)

quoted

  	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
  	if (ret)
  		goto err_disable_msi;
-- 
2.31.4