Re: [PATCH v3 2/4] media: i2c: ov5645: Switch to assigned-clock-rates
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Date: 2020-03-13 21:16:53
Also in:
linux-devicetree, linux-media, linux-renesas-soc, lkml
Hi Prabakhar, Thank you for the patch. On Fri, Mar 13, 2020 at 09:12:32PM +0000, Lad Prabhakar wrote:
quoted hunk ↗ jump to hunk
This patch switches to assigned-clock-rates for specifying the clock rate. The clk-conf.c internally handles setting the clock rate when assigned-clock-rates is passed. The driver now sets the clock frequency only if the deprecated property clock-frequency is defined instead assigned-clock-rates, this is to avoid breakage with existing DT binaries. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> --- drivers/media/i2c/ov5645.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c index a6c17d1..4fbabf3 100644 --- a/drivers/media/i2c/ov5645.c +++ b/drivers/media/i2c/ov5645.c@@ -1055,6 +1055,7 @@ static int ov5645_probe(struct i2c_client *client) struct device_node *endpoint; struct ov5645 *ov5645; u8 chip_id_high, chip_id_low; + bool set_clk = false;
This isn't used.
quoted hunk ↗ jump to hunk
unsigned int i; u32 xclk_freq; int ret;@@ -1094,12 +1095,18 @@ static int ov5645_probe(struct i2c_client *client) return PTR_ERR(ov5645->xclk); } - ret = of_property_read_u32(dev->of_node, "clock-frequency", &xclk_freq); - if (ret) { - dev_err(dev, "could not get xclk frequency\n"); - return ret; + /* check if deprecated property clock-frequency is defined */ + ret = of_property_read_u32(dev->of_node, "clock-frequency", + &xclk_freq); + if (!ret) { + ret = clk_set_rate(ov5645->xclk, xclk_freq); + if (ret) { + dev_err(dev, "could not set xclk frequency\n"); + return ret; + } } + xclk_freq = clk_get_rate(ov5645->xclk);
I would move this line below the comment. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
quoted hunk ↗ jump to hunk
/* external clock must be 24MHz, allow 1% tolerance */ if (xclk_freq < 23760000 || xclk_freq > 24240000) { dev_err(dev, "external clock frequency %u is not supported\n",@@ -1107,12 +1114,6 @@ static int ov5645_probe(struct i2c_client *client) return -EINVAL; } - ret = clk_set_rate(ov5645->xclk, xclk_freq); - if (ret) { - dev_err(dev, "could not set xclk frequency\n"); - return ret; - } - for (i = 0; i < OV5645_NUM_SUPPLIES; i++) ov5645->supplies[i].supply = ov5645_supply_name[i];
-- Regards, Laurent Pinchart _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel