[PATCH net-next 5/7] net: phy: marvell10g: Force reading of 2.5/5G PMA extended abilities
From: Maxime Chevallier <maxime.chevallier@bootlin.com>
Date: 2019-01-18 15:24:30
Also in:
lkml, netdev
Subsystem:
ethernet phy library, marvell mv88x3310 phy driver, networking drivers, the rest · Maintainers:
Andrew Lunn, Heiner Kallweit, Russell King, Marek Behún, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates whether or not we should read register (1.21) "2.52/5G PMA Extended Abilities", which contains information on the support of 2.5GBASET and 5GBASET. After testing on several variants of PHYS of this family, it appears that bit 14 in (1.11) isn't always set when it should be. PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET, but don't have 1.11.14 set. Their register 1.21 is filled with the correct values, indicating 2.5G and 5G support. PHYs 88X2110 do have their 1.11.14 bit set, as it should. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> --- drivers/net/phy/marvell10g.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index f45ddf3bc138..0a35bf0fac47 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c@@ -251,7 +251,7 @@ static int mv3310_resume(struct phy_device *phydev) static int mv3310_config_init(struct phy_device *phydev) { - int ret; + int ret, val; /* Check that the PHY interface type is compatible */ if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
@@ -265,6 +265,23 @@ static int mv3310_config_init(struct phy_device *phydev) if (ret) return ret; + /* Some PHYs in the Alaska family such as the 88X3310 and the 88E2010 + * don't set bit 14 in PMA Extended Abilities (1.11), although they do + * support 2.5GBASET and 5GBASET. Their 2.5/5G PMA Extended abilities + * (1.21) still have a meaningful value, so read it anyway to make sure + * we enable support for these modes if needed. + */ + val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_NG_EXTABLE); + if (val < 0) + return val; + + if (val & MDIO_PMA_NG_EXTABLE_2_5GBT) + __set_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, + phydev->supported); + if (val & MDIO_PMA_NG_EXTABLE_5GBT) + __set_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT, + phydev->supported); + /* Make sure we advertise all the supported modes, and not just the * default one specified in the driver's .features. */
--
2.19.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel