Hi Boris,

On Thursday 10 July 2014 14:56:26 Boris BREZILLON wrote:

On Thu, 10 Jul 2014 13:16:21 +0200 Laurent Pinchart wrote:

quoted

On Monday 07 July 2014 18:42:59 Boris BREZILLON wrote:

quoted

The Atmel HLCDC (HLCD Controller) IP available on some Atmel SoCs (i.e.
at91sam9n12, at91sam9x5 family or sama5d3 family) provides a display
controller device.

The HLCDC block provides a single RGB output port, and only supports LCD
panels connection to LCD panels for now.

The atmel,panel property link the HLCDC RGB output with the LCD panel
connected on this port (note that the HLCDC RGB connector implementation
makes use of the DRM panel framework).

Connection to other external devices (DRM bridges) might be added later
by mean of a new atmel,xxx (atmel,bridge) property.

Signed-off-by: Boris BREZILLON <redacted>
---

 .../devicetree/bindings/drm/atmel-hlcdc-dc.txt     | 59 +++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644
 Documentation/devicetree/bindings/drm/atmel-hlcdc-dc.txt

diff --git a/Documentation/devicetree/bindings/drm/atmel-hlcdc-dc.txt

b/Documentation/devicetree/bindings/drm/atmel-hlcdc-dc.txt new file mode
100644
index 0000000..594bdb2

--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/atmel-hlcdc-dc.txt

@@ -0,0 +1,59 @@
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver
+
+The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD

device.
+See Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt for more
details.
+
+Required properties:
+ - compatible: value should be one of the following:
+   "atmel,hlcdc-dc"
+ - interrupts: the HLCDC interrupt definition
+ - pinctrl-names: the pin control state names. Should contain
"default",
+   "rgb-444", "rgb-565", "rgb-666" and "rgb-888".
+ - pinctrl-[0-4]: should contain the pinctrl states described by
pinctrl
+   names.

Do you need to switch between the different pinctrl configurations at
runtime, or is the configuration selected from the panel type, which
doesn't change ?

At the moment no, but if we ever need to support different devices on
the same RGB connector (actually Atmel's sama5d3xek boards have an
RGB to HDMI bridge connected on the same RGB connector) and these
devices do not support the same RGB mode (say your LCD panel supports
RGB888 and your RGB to HDMI bridge supports RGB555), then depending on
the output you select you'll have to change your pinctrl config at
runtime.

Just to make sure I understand the use case correctly, are you talking about 
two devices (for example an RGB666 panel and an RGB888 RGB to HDMI bridge) 
connected to the same output, with the ability to switch between the two at 
runtime ? That's a valid case (on a side note we shouldn't forget that the 
option of using both devices at the same time should be supported as well), 
but I would probably go for a fixed pinctrl configuration that supports both, 
although switching configurations at runtime would be a micro-optimization 
that might make sense.

I'd say we could get rid of this runtime pinctrl config as a first step
if DT ABI stability was not required.
But it is, and I'd like to have a future proof binding to handle these
tricky cases when they occurs (if they ever do).

I think we have a shortcoming of the pinctrl API here in the general case. The 
API only allows you to select a single configuration per device. Imagine the 
same display controller, with two DPI outputs, each of them configurable in 
444, 565, 666 or 888 modes. With the current API we would have to create 4*4 = 
16 pinctrl configurations for all combinations. That obviously wouldn't scale, 
so we'll have to fix this eventually. From a DT stability point of view, I 
would thus avoid specifying multiple pinctrl configurations now until we come 
up with a standard way to support this use case.

Anyway, I'm open to any other alternative that could let me add support
for this later on.

BTW, is there any reason for not defining an RGB connector type (I'm
currently defining HLCDC connector as an LVDS connector) ?

Not that I know of. The DRM API has been developed before display on embedded 
systems became such a hot topic. If we had to redo it today, panels might be 
exposed to userspace as such, with a connector. We have to live with the past, 
so the connector will stay, but adding a new RGB connector type could make 
sense (although we might need a different name, in a way the VGA and LVDS 
connectors also carry RGB signals).

quoted

quoted

+ - atmel,panel: Should contain a phandle with 2 parameters.
+   The first cell is a phandle to a DRM panel device
+   The second cell encodes the RGB mode, which can take the following
values:
+   * 0: RGB444
+   * 1: RGB565
+   * 2: RGB666
+   * 3: RGB888
+   The third cell encodes specific flags describing LCD signals
configuration
+   (see Atmel's datasheet for a full description of these
fields):
+   * bit 0: HSPOL: Horizontal Synchronization Pulse Polarity
+   * bit 1: VSPOL: Vertical Synchronization Pulse Polarity
+   * bit 2: VSPDLYS: Vertical Synchronization Pulse Start
+   * bit 3: VSPDLYE: Vertical Synchronization Pulse End
+   * bit 4: DISPPOL: Display Signal Polarity
+   * bit 7: DISPDLY: LCD Controller Display Power Signal
Synchronization
+   * bit 12: VSPSU: LCD Controller Vertical synchronization Pulse Setup
Configuration
+   * bit 13: VSPHO: LCD Controller Vertical synchronization Pulse Hold
Configuration
+   * bit 16-20: GUARDTIME: LCD DISPLAY Guard Time

If I'm not mistaken, those are HLCDC configuration values that depend on
the panel type and characteristics. Shouldn't they then be queries from
the panel through the drm_panel API at runtime instead of being specified
in DT ? This would likely require extending the drm_panel API.

HSPOL and VSPOL can be deduced from DRM_MODE_FLAG_[PN]HSYNC and
DRM_MODE_FLAG_[PN]VSYNC, I'm not sure for the other flags or the
GUARDTIME value.

Another question I had regarding these flags is whether they were LCD
panel specific or a mix of panel and board implementation.
Take the VSYNC HSYNC polarity, of course the LCD panel defines what it
expects in terms of polarity, but nothing prevents the HW designer from
inverting the VSYNC/HSYNC polarity (expect common sense :-)), right ?

A solution would be to override some drm_display_mode settings with
informations taken from the DT.

Given that I gave the exact same argument during a V4L2 DT bindings design 
review, I can only agree :-) It thus makes sense to specify polarities in the 
HLCDC DT node. The RGB mode, however, should probably be queried from the 
panel, as I don't expect it to be board-dependent but only panel-dependent.

I'm not sure about the other bits in the third cell, maybe we should discuss 
them in more details. I'm always wary when I see DT bindings referring to a 
datasheet :-) Getting the information from the panel by default, with a 
possible override, is an interesting option. You would thus likely need 
several DT properties associated with each connection to a panel. Would it 
then make sense to use the OF graph DT bindings instead of the atmel,panel 
property to specify connections ? You could store per-connection data in the 
endpoint and/or port nodes.

Thanks for your review.

You're welcome. Sorry for not having had time to review the driver itself. 
Given my limited bandwidth at the moment I've decided to concentrate on the DT 
bindings first.

-- 
Regards,

Laurent Pinchart