[PATCH net-next v2 06/14] selftests: dpll: add pin state tests

@@ -8,6 +8,7 @@ TEST_INCLUDES := \
 
 TEST_PROGS := \
 	dpll_basic.sh \
+	dpll_features.sh \
 	dpll_stress.sh \
 # end of TEST_PROGS
 

@@ -0,0 +1,183 @@
+#!/bin/bash
+# SPDX-License-Identifier: GPL-2.0
+#
+# DPLL device and pin feature tests. Exercises individual dpll_device_ops
+# and dpll_pin_ops callbacks, verifying get/set roundtrips through the
+# netlink interface. By default a dpllsim device with a known pin layout
+# is created; set DPLL_DEV_ID to run against an existing device instead,
+# the simulator-only tests then skip unless that device is a dpllsim one.
+#
+# Copyright (c) 2026 Red Hat, Inc.
+
+SCRIPTDIR=$(dirname "$(readlink -e "${BASH_SOURCE[0]}")")
+
+source "$SCRIPTDIR/../../../net/lib.sh"
+source "$SCRIPTDIR/../lib/sh/dpll_lib.sh"
+
+ALL_TESTS="
+	test_pin_state_transitions
+"
+
+##############################################################################
+# Pin-level feature tests
+
+test_pin_state_transitions()
+{
+	local before state after reason
+
+	RET=0
+
+	if [ -z "$PIN_TUNE_ID" ]; then
+		dpll_log_test_skip_or_fail "DPLL pin state transitions" \
+		    "no spare input pin"
+		return
+	fi
+	if ! dpll_pin_set_supports state; then
+		log_test_skip "DPLL pin state transitions" \
+		    "dpll tool lacks pin set state"
+		return
+	fi
+	if ! dpll_pin_has_capability "$PIN_TUNE_ID" state-can-change; then
+		dpll_log_test_skip_or_fail "DPLL pin state transitions" \
+		    "state cannot change"
+		return
+	fi
+
+	before=$(dpll_pin_get_state "$DPLL_DEV_ID" "$PIN_TUNE_ID")
+	if [ -z "$before" ]; then
+		dpll_log_test_skip_or_fail "DPLL pin state transitions" \
+		    "state not reported"
+		return
+	fi
+	# Restore the original state even when the test aborts half way.
+	defer dpll_pin_set_state "$DPLL_DEV_ID" "$PIN_TUNE_ID" "$before"
+
+	# The pin is not connected, see how PIN_TUNE_ID is picked, and the
+	# test never connects it, it moves the pin between the disconnected
+	# and selectable states only and ends at the original one. A pin
+	# that is connected may become the reference the device locks to.
+	#
+	# A driver may refuse a state the capability promises, for a
+	# constraint the interface does not tell. On a device provided by
+	# the user that is a skip with the reason the tool reported, on
+	# the created device a failure, the simulator accepts both states.
+	# The test ends there, whichever set was refused, a state that was
+	# not set has nothing to read back and the deferred restore puts
+	# the pin back. A refused restore is treated the same way when
+	# nothing failed before it, afterwards it is one more failure, a
+	# skip would hide the earlier one.
+	for state in disconnected selectable; do
+		if ! dpll_pin_set_state "$DPLL_DEV_ID" "$PIN_TUNE_ID" \
+					"$state"; then
+			reason=${DPLL_LAST_ERR%%$'\n'*}
+			dpll_log_test_skip_or_fail \
+			    "DPLL pin state transitions" \
+			    "cannot set pin state to $state${reason:+, $reason}"
+			return
+		fi
+		after=$(dpll_pin_get_state "$DPLL_DEV_ID" "$PIN_TUNE_ID")
+		if [ "$after" != "$state" ]; then
+			check_err 1 "pin not $state, state '$after'"
+		fi
+	done
+
+	if ! dpll_pin_set_state "$DPLL_DEV_ID" "$PIN_TUNE_ID" "$before"; then
+		reason=${DPLL_LAST_ERR%%$'\n'*}
+		reason=${reason:+, $reason}
+		if [ "$RET" -eq 0 ]; then
+			dpll_log_test_skip_or_fail \
+			    "DPLL pin state transitions" \
+			    "cannot set pin state to $before$reason"
+			return
+		fi
+		check_err 1 "cannot restore pin state$reason"
+	fi
+	after=$(dpll_pin_get_state "$DPLL_DEV_ID" "$PIN_TUNE_ID")
+	if [ "$after" != "$before" ]; then
+		check_err 1 "pin state not restored, got '$after'"
+	fi
+
+	log_test "DPLL pin state transitions"
+}
+
+##############################################################################
+
+cleanup()
+{
+	# A second signal must not abort the teardown half way.
+	trap '' INT TERM
+
+	# Run the pending restores of an interrupted test first, the device
+	# they apply to may be one the user provided.
+	defer_scopes_cleanup
+	if [ -n "$DPLL_CREATED_DEVICE" ]; then
+		dpllsim_delete_device "$DPLL_CREATED_DEVICE" ||
+			log_info "cannot delete device $DPLL_CREATED_DEVICE"
+	fi
+	# The device whose creation a signal interrupted is recorded by the
+	# library alone, a double delete of a tracked one is harmless.
+	if [ -n "$DPLLSIM_CREATED_NAME" ]; then
+		dpllsim_delete_device "$DPLLSIM_CREATED_NAME" ||
+			log_info "cannot delete device $DPLLSIM_CREATED_NAME"
+	fi
+	dpll_lib_cleanup
+}
+
+dpll_lib_check_prereqs
+# Another run would find the devices of this one left behind, see the
+# lock in the library.
+dpll_lib_lock
+
+# The module check may mount configfs, so the exit trap that unmounts it
+# again has to be in place before. INT and TERM exit through it as well,
+# so that a timeout imposed by the harness still restores the device.
+trap cleanup EXIT
+trap 'exit 1' INT TERM
+
+if [ -n "${DPLL_DEV_ID:-}" ]; then
+	dpll_lib_init
+else
+	dpllsim_check_module
+	if ! dpllsim_setup_standard_device; then
+		echo "SKIP: cannot create dpllsim device"
+		exit "$ksft_skip"
+	fi
+	DPLL_DEV_ID=$DPLLSIM_DEV_ID
+	DPLL_CREATED_DEVICE=$DPLLSIM_CREATED_NAME
+	DPLL_MODULE_NAME="dpllsim"
+fi
+
+log_info "testing DPLL device $DPLL_DEV_ID (module $DPLL_MODULE_NAME)"
+
+# PIN_TUNE_ID is the input pin the tests reconfigure. It must not be the
+# reference the device is locked to, so it is the first input pin that
+# is not connected on the device. When the first dumped input pin and
+# another one both qualify the other one is taken, so that the first
+# pin, the one a simulated device locks to once it is connected, is left
+# alone. Tests that need the pin skip when there is none rather than
+# reconfiguring the reference.
+pick_tune_pin()
+{
+	local pin_id state
+
+	PIN_TUNE_ID=""
+	for pin_id in "${input_pins[@]}"; do
+		state=$(dpll_pin_get_state "$DPLL_DEV_ID" "$pin_id")
+		case "$state" in
+		disconnected|selectable)
+			;;
+		*)
+			continue
+			;;
+		esac
+		PIN_TUNE_ID=$pin_id
+		[ "$pin_id" != "${input_pins[0]}" ] && return
+	done
+}
+
+mapfile -t input_pins < <(dpll_pin_find_by_direction "$DPLL_DEV_ID" input)
+pick_tune_pin
+
+tests_run
+
+exit $EXIT_STATUS

@@ -15,6 +15,7 @@ source "$SCRIPTDIR/../lib/sh/dpll_lib.sh"
 
 ALL_TESTS="
 	test_rapid_create_delete
+	test_pin_state_flooding
 	test_deploy_cycle
 "
 

@@ -45,6 +46,7 @@ cleanup()
 	# A second signal must not abort the teardown half way.
 	trap '' INT TERM
 
+	defer_scopes_cleanup
 	for dev in "${CREATED_DEVICES[@]}"; do
 		dpllsim_delete_device "$dev" ||
 			log_info "cannot delete device $dev"

@@ -133,6 +135,61 @@ test_rapid_create_delete()
 	log_test "DPLL rapid create/delete ($STRESS_ITERATIONS iterations)"
 }
 
+test_pin_state_flooding()
+{
+	local clock_id name dev_id pin_id i last state fails=0
+	local states=(connected disconnected selectable)
+
+	RET=0
+
+	if ! dpll_pin_set_supports state; then
+		log_test_skip "DPLL pin state flooding" \
+			      "dpll tool lacks pin set state"
+		return
+	fi
+
+	dpllsim_alloc_clock_id; clock_id=$DPLLSIM_CLOCK_ID
+	if ! create_stress_device "$clock_id" 10; then
+		check_err 1 "cannot create device"
+		log_test "DPLL pin state flooding"
+		return
+	fi
+	name=$DPLLSIM_CREATED_NAME
+	track_device "$name"
+
+	if ! dev_id=$(dpll_device_wait_by_clock_id "$clock_id" dpllsim); then
+		check_err 1 "device not visible on netlink"
+	else
+		pin_id=$(dpll_pin_find_by_direction "$dev_id" input | head -1)
+		if [ -z "$pin_id" ]; then
+			check_err 1 "no input pin on stress device"
+		else
+			for i in $(seq 1 50); do
+				last=${states[i % 3]}
+				dpll_pin_set_state "$dev_id" "$pin_id" \
+						   "$last" ||
+					fails=$((fails + 1))
+			done
+			if [ "$fails" -gt 0 ]; then
+				check_err 1 "$fails of 50 state changes failed"
+			fi
+			state=$(dpll_pin_get_state "$dev_id" "$pin_id")
+			if [ "$state" != "$last" ]; then
+				check_err 1 \
+				    "state expected '$last', got '$state'"
+			fi
+		fi
+	fi
+
+	if dpllsim_delete_device "$name"; then
+		untrack_device "$name"
+	else
+		check_err 1 "cannot delete device $name"
+	fi
+
+	log_test "DPLL pin state flooding"
+}
+
 test_deploy_cycle()
 {
 	local clock_id name i

@@ -5,7 +5,8 @@
 # tool and around the dpllsim configfs interface for creating virtual DPLL
 # devices. Sourcing this file has no side effects; call
 # dpll_lib_check_prereqs and dpll_lib_init explicitly. net/lib.sh must be
-# sourced first, it provides ksft_skip, busywait and log_info.
+# sourced first, it provides ksft_skip, busywait and log_info to the
+# library and defer to the scripts.
 #
 # Copyright (c) 2026 Red Hat, Inc.
 #

@@ -86,6 +87,44 @@ dpll_lib_lock()
 	fi
 }
 
+# Print the usage block of the given command of the given object from
+# the help of the dpll tool, "dpll pin set" for instance. The help lists
+# one usage per command, each starting with "Usage: dpll <obj> <cmd>" or
+# with "dpll <obj> <cmd>" indented under the first, possibly wrapped
+# over further lines. The block starts at the line that names the
+# command, with a space after the name so that a command whose name
+# merely begins the same way does not match, and ends before the next
+# line that names another command of the object, or at the end of the
+# help when none follows. Return 1 when the help has no usage for the
+# command, in which case nothing is printed.
+__dpll_usage_block()
+{
+	local obj=$1
+	local cmd=$2
+
+	dpll "$obj" help 2>&1 | \
+		awk -v start="[[:space:]]dpll $obj $cmd([[:space:]]|$)" \
+		    -v other="[[:space:]]dpll $obj [a-z-]+([[:space:]]|$)" \
+		    '$0 ~ start { s = 1; print; next }
+		     s && $0 ~ other { exit }
+		     s { print }
+		     END { exit !s }'
+}
+
+# Return 0 when the dpll tool knows the given "pin set" keyword, such as
+# state or frequency. A test that sets something checks its keyword
+# first and skips on a tool that is too old for it. Only the "pin set"
+# usage is searched, a keyword that only "pin show" knows must not
+# count, and the keyword must stand on its own between blanks or
+# brackets, a hyphenated compound that contains it does not count.
+dpll_pin_set_supports()
+{
+	local usage
+
+	usage=$(__dpll_usage_block pin set) || return 1
+	grep -qE "(^|[[:space:][])$1([[:space:]]|$)" <<< "$usage"
+}
+
 # Detect the DPLL device to test. DPLL_DEV_ID may be set by the user to
 # force a specific device; an empty value means auto-detect, which takes
 # the first device that is not a dpllsim one, so that an instance of the

@@ -323,6 +362,41 @@ dpll_pin_get_state()
 	__dpll_pin_dev_field "$1" "$2" '.state'
 }
 
+# Return 0 when the pin advertises the given capability, named as
+# iproute2 prints it (state-can-change, priority-can-change, ...).
+dpll_pin_has_capability()
+{
+	local pin_id=$1
+	local name=$2
+	local out
+
+	out=$(dpll pin show id "$pin_id" -j 2>/dev/null) || return 1
+	jq -e --arg name "$name" \
+	   '(.pin[0]? // .) | .capabilities | index($name) != null' \
+	   <<< "$out" &> /dev/null
+}
+
+##############################################################################
+# Pin setters
+#
+# Every setter returns the status of the tool and keeps what the tool
+# printed on stderr in DPLL_LAST_ERR, the "Error: ..." line that carries
+# the extack message of the kernel, so that a caller can tell a refusal
+# it may skip on from a failure.
+
+DPLL_LAST_ERR=""
+
+# $3: connected / disconnected / selectable
+dpll_pin_set_state()
+{
+	local dev_id=$1
+	local pin_id=$2
+	local state=$3
+
+	DPLL_LAST_ERR=$(dpll pin set id "$pin_id" parent-device "$dev_id" \
+			     state "$state" 2>&1 >/dev/null)
+}
+
 ##############################################################################
 # dpllsim configfs interface
 #