Re: [PATCH net-next v3 13/14] ravb: Update ravb_emac_init_gbeth()

On 10/12/21 8:52 PM, Biju Das wrote:

quoted

quoted

This patch enables Receive/Transmit port of TOE and removes the
setting of promiscuous bit from EMAC configuration mode register.

This patch also update EMAC configuration mode comment from "PAUSE
prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX; RX; CRC
Pass Through".

   I'm not sure why you set ECMR.RCPT while you don't have the checksum
offloaded...

quoted

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
v2->v3:
 * Enabled TPE/RPE of TOE, as disabling causes loopback test to fail
 * Documented CSR0 register bits
 * Removed PRM setting from EMAC configuration mode
 * Updated EMAC configuration mode.
v1->v2:
 * No change
V1:
 * New patch.
---
 drivers/net/ethernet/renesas/ravb.h      | 6 ++++++
 drivers/net/ethernet/renesas/ravb_main.c | 5 +++--
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/renesas/ravb.h

b/drivers/net/ethernet/renesas/ravb.h
index 69a771526776..08062d73df10 100644

--- a/drivers/net/ethernet/renesas/ravb.h
+++ b/drivers/net/ethernet/renesas/ravb.h

@@ -204,6 +204,7 @@ enum ravb_reg {
 	TLFRCR	= 0x0758,
 	RFCR	= 0x0760,
 	MAFCR	= 0x0778,
+	CSR0    = 0x0800,	/* RZ/G2L only */
 };

@@ -964,6 +965,11 @@ enum CXR31_BIT {
 	CXR31_SEL_LINK1	= 0x00000008,
 };

+enum CSR0_BIT {
+	CSR0_TPE	= 0x00000010,
+	CSR0_RPE	= 0x00000020,
+};
+

  Is this really needed if you have ECMR.RCPT cleared?

Yes it is required. Please see the current log and log with the changes you suggested

root@smarc-rzg2l:/rzg2l-test-scripts# ./eth_t_001.sh
[   39.646891] ravb 11c20000.ethernet eth0: Link is Down
[   39.715127] ravb 11c30000.ethernet eth1: Link is Down
[   39.895680] Microchip KSZ9131 Gigabit PHY 11c20000.ethernet-ffffffff:07: attached PHY driver (mii_bus:phy_addr=11c20000.ethernet-ffffffff:07, irq=POLL)
[   39.966370] Microchip KSZ9131 Gigabit PHY 11c30000.ethernet-ffffffff:07: attached PHY driver (mii_bus:phy_addr=11c30000.ethernet-ffffffff:07, irq=POLL)
[   42.988573] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   42.995119] ravb 11c20000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   43.052541] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   43.055710] ravb 11c30000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off

EXIT|PASS||[422391:43:00] ||

root@smarc-rzg2l:/rzg2l-test-scripts#


with the changes you suggested
----------------------------

root@smarc-rzg2l:/rzg2l-test-scripts# ./eth_t_001.sh
[   23.300520] ravb 11c20000.ethernet eth0: Link is Down
[   23.535604] ravb 11c30000.ethernet eth1: device will be stopped after h/w processes are done.
[   23.547267] ravb 11c30000.ethernet eth1: Link is Down
[   23.802667] Microchip KSZ9131 Gigabit PHY 11c20000.ethernet-ffffffff:07: attached PHY driver (mii_bus:phy_addr=11c20000.ethernet-ffffffff:07, irq=POLL)
[   24.031711] ravb 11c30000.ethernet eth1: failed to switch device to config mode
RTNETLINK answers: Connection timed out

EXIT|FAIL||[422391:42:32] Failed to bring up ETH1||

root@smarc-rzg2l:/rzg2l-test-scripts#

   Hm... :-/
   What if you only clear ECMR.RCPT but continue to set CSR0?

MBR, Sergey