RE: [EXT] Re: [PATCH net] net: phylink: fix link state on phy-connect

The attached p21 patch doesn't change anything.
But another one from the mail-text is good
	void phylink_disconnect_phy(struct phylink *pl)
	+		pl->phy_state.link = false;

There still (not for my MRVL-PP2) problem:
	It is expected that on  ifconfig-down the callback
		pl->ops->mac_link_down(ndev, pl->link_an_mode);
would be called, but it isn't


-----Original Message-----
From: Russell King - ARM Linux [mailto:linux@armlinux.org.uk] 
Sent: Wednesday, November 29, 2017 9:59 PM
To: Yan Markman <redacted>
Cc: Antoine Tenart <redacted>; andrew@lunn.ch; f.fainelli@gmail.com; davem@davemloft.net; gregory.clement@free-electrons.com; thomas.petazzoni@free-electrons.com; miquel.raynal@free-electrons.com; Nadav Haklai <redacted>; mw@semihalf.com; Stefan Chulski <redacted>; netdev@vger.kernel.org; linux-kernel@vger.kernel.org
Subject: [EXT] Re: [PATCH net] net: phylink: fix link state on phy-connect

External Email

----------------------------------------------------------------------
On Wed, Nov 29, 2017 at 07:33:44PM +0000, Yan Markman wrote:

Hi Russel

On my board I have [Marvell 88E1510] phy working with STATUS-POLLING I 
see some inconsistencies  -- first ifconfig-up is different from furthers, no "link is down" reports.
Please refer the behavior example below.
My patch is a "simple solution"  -- always reset/clear Link-state-parameters before going UP.
Possibly, more correct (but much more complicated) solution would be in the   phy state machine   and   phylink resolve modification.
I just found that 
    On ifconfig-down, the phy-state-machine and phylink-resolve
    are stopped before executing before passing over full graceful down/reset state.
    The further ifconfig-up starts with old state parameters.
Special cases not-tested but logic 2 test-cases are:
   remote side changes speed whilst link is Down or Disconnected. But local ifconfig-up starts with old speed.

Hi,

I think this is covered in my "phy" branch - but could probably do with further testing, specifically this patch (which I've attached):

"phylink: ensure we take the link down when phylink_stop() is called"

This takes the link down on the MAC side synchronously when phylink_stop() is called.  However, I think your case might also benefit from this patch - please test the patch referred to without this change, and let me know if you need this change to solve your problem:

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c index 8f43f8779317..c90ad50204b0 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c

@@ -798,6 +798,7 @@ void phylink_disconnect_phy(struct phylink *pl)
 		mutex_lock(&pl->state_mutex);
 		pl->netdev->phydev = NULL;
 		pl->phydev = NULL;
+		pl->phy_state.link = false;
 		mutex_unlock(&pl->state_mutex);
 		mutex_unlock(&phy->lock);
 		flush_work(&pl->resolve);

Thanks.

--
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 8.8Mbps down 630kbps up According to speedtest.net: 8.21Mbps down 510kbps up