Re: [PATCH net-next 4/6] net: use core MTU range checking in core net infra

From
Sabrina Dubroca <sd@queasysnail.net>
Date
2016-10-19 15:28:13
Also in
lkml
Reply to
Jarod Wilson, 2016-10-19
2016-10-19, 10:40:06 -0400, Jarod Wilson wrote:
On Wed, Oct 19, 2016 at 03:55:29PM +0200, Sabrina Dubroca wrote:
quoted
2016-10-18, 22:33:31 -0400, Jarod Wilson wrote:
quoted
geneve:
- Merge __geneve_change_mtu back into geneve_change_mtu, set max_mtu
- This one isn't quite as straight-forward as others, could use some
  closer inspection and testing

macvlan:
- set min/max_mtu

tun:
- set min/max_mtu, remove tun_net_change_mtu

vxlan:
- Merge __vxlan_change_mtu back into vxlan_change_mtu, set min/max_mtu
- This one is also not as straight-forward and could use closer inspection
  and testing from vxlan folks

bridge:
- set max_mtu via br_min_mtu()

openvswitch:
- set min/max_mtu, remove internal_dev_change_mtu
- note: max_mtu wasn't checked previously, it's been set to 65535, which
  is the largest possible size supported

sch_teql:
- set min/max_mtu (note: max_mtu previously unchecked, used max of 65535)
Nothing for other virtual netdevices? (dummy, veth, bond, etc) Their
MTU is limited to 1500 now.  Also missing macsec and ip_gre, probably
others that are using ether_setup.
Yeah, I've clearly missed more than I thought. Doing another sweep now.
Thanks.

I'm thinking more and more that we ought to back out the patch that sets
min/max in ether_setup, save it for last, after we're sure everyone that
calls it has been prepared.
I'm not sure how that would work now, if some of the patches that
already went in for ethernet drivers assume that ether_setup will
configure a basic {min,max}_mtu pair (at least e100 makes that
assumption, but that might be the only one).
quoted
[...]
quoted
diff --git a/net/bridge/br_device.c b/net/bridge/br_device.c
index 89a687f..81fc79a 100644
--- a/net/bridge/br_device.c
+++ b/net/bridge/br_device.c
@@ -184,17 +184,15 @@ static struct rtnl_link_stats64 *br_get_stats64(struct net_device *dev,
 
 static int br_change_mtu(struct net_device *dev, int new_mtu)
 {
+#if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	struct net_bridge *br = netdev_priv(dev);
-	if (new_mtu < 68 || new_mtu > br_min_mtu(br))
-		return -EINVAL;
-
-	dev->mtu = new_mtu;
 
-#if IS_ENABLED(CONFIG_BRIDGE_NETFILTER)
 	/* remember the MTU in the rtable for PMTU */
 	dst_metric_set(&br->fake_rtable.dst, RTAX_MTU, new_mtu);
 #endif
 
+	dev->mtu = new_mtu;
+
 	return 0;
 }
 
@@ -390,6 +388,7 @@ void br_dev_setup(struct net_device *dev)
 	dev->hw_features = COMMON_FEATURES | NETIF_F_HW_VLAN_CTAG_TX |
 			   NETIF_F_HW_VLAN_STAG_TX;
 	dev->vlan_features = COMMON_FEATURES;
+	dev->max_mtu = br_min_mtu(br);
br_min_mtu uses br->port_list, which is only initialized a few lines
later (right after the spin_lock_init() at the end of the context of
this diff).
Ah, okay, I'd just grouped it with the other dev->foo settings.
quoted
Besides, I don't think this works: br_min_mtu(br) changes when you add
and remove ports, or when you change the MTU of an enslaved
device. But this makes the max MTU for the bridge fixed (to 1500).
Okay, how about this: set no max_mtu (or set it to IP_MAX_MTU/65535), and
then retain a check against the possibly ever-changing br_min_mtu(br) in
br_change_mtu()?
Sounds good to me.


-- 
Sabrina
Thread (63 messages) 63 messages, 15 authors, last reply 2016-10-30
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help