@@ -274,23 +274,6 @@ config DM9000_FORCE_SIMPLE_PHY_POLL
 	  costly MII PHY reads. Note, this will not work if the chip is
 	  operating with an external PHY.
 
-config ENC28J60
-	tristate "ENC28J60 support"
-	depends on EXPERIMENTAL && SPI && NET_ETHERNET
-	select CRC32
-	---help---
-	  Support for the Microchip EN28J60 ethernet chip.
-
-	  To compile this driver as a module, choose M here. The module will be
-	  called enc28j60.
-
-config ENC28J60_WRITEVERIFY
-	bool "Enable write verify"
-	depends on ENC28J60
-	---help---
-	  Enable the verify after the buffer write useful for debugging purpose.
-	  If unsure, say N.
-
 config NET_PCI
 	bool "EISA, VLB, PCI and on board controllers"
 	depends on ISA || EISA || PCI

@@ -53,7 +53,6 @@ obj-$(CONFIG_TUN) += tun.o
 obj-$(CONFIG_VETH) += veth.o
 obj-$(CONFIG_NET_NETX) += netx-eth.o
 obj-$(CONFIG_DM9000) += dm9000.o
-obj-$(CONFIG_ENC28J60) += enc28j60.o
 
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_ETHERNET) += ethernet/

@@ -78,6 +78,7 @@ config LANTIQ_ETOP
 source "drivers/net/ethernet/marvell/Kconfig"
 source "drivers/net/ethernet/mellanox/Kconfig"
 source "drivers/net/ethernet/micrel/Kconfig"
+source "drivers/net/ethernet/microchip/Kconfig"
 
 config MIPS_SIM_NET
 	tristate "MIPS simulator Network device"

@@ -36,6 +36,7 @@ obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
 obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
 obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
 obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
+obj-$(CONFIG_NET_VENDOR_MICROCHIP) += microchip/
 obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
 obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
 obj-$(CONFIG_FEALNX) += fealnx.o

@@ -0,0 +1,33 @@
+#
+# Microchip network device configuration
+#
+
+config NET_VENDOR_MICROCHIP
+	bool "Microchip devices"
+	depends on SPI && EXPERIMENTAL
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Microchip cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+config ENC28J60
+	tristate "ENC28J60 support"
+	depends on NET_VENDOR_MICROCHIP && SPI && EXPERIMENTAL
+	select CRC32
+	---help---
+	  Support for the Microchip EN28J60 ethernet chip.
+
+	  To compile this driver as a module, choose M here. The module will be
+	  called enc28j60.
+
+config ENC28J60_WRITEVERIFY
+	bool "Enable write verify"
+	depends on ENC28J60
+	---help---
+	  Enable the verify after the buffer write useful for debugging purpose.
+	  If unsure, say N.

@@ -0,0 +1,5 @@
+#
+# Makefile for the Microchip network device drivers.
+#
+
+obj-$(CONFIG_ENC28J60) += enc28j60.o