Re: [PATCH v26 10/22] x86/sgx: Linux Enclave Driver

From
Jordan Hand <hidden>
Date
2020-02-19 03:26:34
Also in
lkml
Reply to
Jarkko Sakkinen, 2020-02-09
I ran our validation tests for the Open Enclave SDK against this patch
set and came across a potential issue.

On 2/9/20 1:25 PM, Jarkko Sakkinen wrote:
quoted hunk ↗ jump to hunk
+/**
+ * sgx_encl_may_map() - Check if a requested VMA mapping is allowed
+ * @encl:		an enclave
+ * @start:		lower bound of the address range, inclusive
+ * @end:		upper bound of the address range, exclusive
+ * @vm_prot_bits:	requested protections of the address range
+ *
+ * Iterate through the enclave pages contained within [@start, @end) to verify
+ * the permissions requested by @vm_prot_bits do not exceed that of any enclave
+ * page to be mapped.  Page addresses that do not have an associated enclave
+ * page are interpreted to zero permissions.
+ *
+ * Return:
+ *   0 on success,
+ *   -EACCES if VMA permissions exceed enclave page permissions
+ */
+int sgx_encl_may_map(struct sgx_encl *encl, unsigned long start,
+		     unsigned long end, unsigned long vm_prot_bits)
+{
+	unsigned long idx, idx_start, idx_end;
+	struct sgx_encl_page *page;
+
+	/* PROT_NONE always succeeds. */
+	if (!vm_prot_bits)
+		return 0;
+
+	idx_start = PFN_DOWN(start);
+	idx_end = PFN_DOWN(end - 1);
+
+	for (idx = idx_start; idx <= idx_end; ++idx) {
+		mutex_lock(&encl->lock);
+		page = radix_tree_lookup(&encl->page_tree, idx);
+		mutex_unlock(&encl->lock);
+
+		if (!page || (~page->vm_max_prot_bits & vm_prot_bits))
+			return -EACCES;
+	}
+
+	return 0;
+}
+static struct sgx_encl_page *sgx_encl_page_alloc(struct sgx_encl *encl,
+						 unsigned long offset,
+						 u64 secinfo_flags)
+{
+	struct sgx_encl_page *encl_page;
+	unsigned long prot;
+
+	encl_page = kzalloc(sizeof(*encl_page), GFP_KERNEL);
+	if (!encl_page)
+		return ERR_PTR(-ENOMEM);
+
+	encl_page->desc = encl->base + offset;
+	encl_page->encl = encl;
+
+	prot = _calc_vm_trans(secinfo_flags, SGX_SECINFO_R, PROT_READ)  |
+	       _calc_vm_trans(secinfo_flags, SGX_SECINFO_W, PROT_WRITE) |
+	       _calc_vm_trans(secinfo_flags, SGX_SECINFO_X, PROT_EXEC);
+
+	/*
+	 * TCS pages must always RW set for CPU access while the SECINFO
+	 * permissions are *always* zero - the CPU ignores the user provided
+	 * values and silently overwrites them with zero permissions.
+	 */
+	if ((secinfo_flags & SGX_SECINFO_PAGE_TYPE_MASK) == SGX_SECINFO_TCS)
+		prot |= PROT_READ | PROT_WRITE;
+
+	/* Calculate maximum of the VM flags for the page. */
+	encl_page->vm_max_prot_bits = calc_vm_prot_bits(prot, 0);
During mprotect (in mm/mprotect.c line 525) the following checks if
READ_IMPLIES_EXECUTE and a PROT_READ is being requested. If so and
VM_MAYEXEC is set, it also adds PROT_EXEC to the request.

	if (rier && (vma->vm_flags & VM_MAYEXEC))
		prot |= PROT_EXEC;

But if we look at sgx_encl_page_alloc(), we see vm_max_prot_bits is set
without taking VM_MAYEXEC into account:

	encl_page->vm_max_prot_bits = calc_vm_prot_bits(prot, 0);

sgx_encl_may_map() checks that the requested protection can be added with:

	if (!page || (~page->vm_max_prot_bits & vm_prot_bits))
		return -EACCESS

This means that for any process where READ_IMPLIES_EXECUTE is set and
page where (vma->vm_flags & VM_MAYEXEC) == true, mmap/mprotect calls to
that request PROT_READ on a page that was not added with PROT_EXEC will
fail.

- Jordan
Thread (24 messages) 24 messages, 7 authors, last reply 2020-02-21
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help