Thread (13 messages) 13 messages, 5 authors, 2020-10-05

[PATCH v2 3/4] ARM: dts: exynos: Add Ethernet to Artik 5 board

flat view
STALE2207d SUPERSEDED

From: Łukasz Stelmach <l.stelmach@samsung.com>
Date: 2020-10-02 19:22:35
Also in: linux-arm-kernel, linux-samsung-soc, lkml, netdev
Subsystem: the rest · Maintainer: Linus Torvalds

Revision v2 of 17 in this series.

Revisions (17)
  1. v2 current
  2. v3 [diff vs current]
  3. v4 [diff vs current]
  4. v5 [diff vs current]
  5. v6 [diff vs current]
  6. v7 [diff vs current]
  7. v8 [diff vs current]
  8. v9 [diff vs current]
  9. v10 [diff vs current]
  10. v11 [diff vs current]
  11. v11 [diff vs current]
  12. v12 [diff vs current]
  13. v13 [diff vs current]
  14. v14 [diff vs current]
  15. v15 [diff vs current]
  16. v16 [diff vs current]
  17. v17 [diff vs current]

Possibly related (same subject, not in this thread)

Add node for ax88796c ethernet chip.

Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
---
 arch/arm/boot/dts/exynos3250-artik5-eval.dts | 21 ++++++++++++++++++++
 1 file changed, 21 insertions(+)
diff --git a/arch/arm/boot/dts/exynos3250-artik5-eval.dts b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
index 20446a846a98..7f115c348a2a 100644
--- a/arch/arm/boot/dts/exynos3250-artik5-eval.dts
+++ b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
@@ -37,3 +37,24 @@ &mshc_2 {
 &serial_2 {
 	status = "okay";
 };
+
+&spi_0 {
+	status = "okay";
+	cs-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>, <0>;
+
+	assigned-clocks        = <&cmu CLK_MOUT_MPLL>, <&cmu CLK_DIV_MPLL_PRE>, <&cmu CLK_MOUT_SPI0>,    <&cmu CLK_DIV_SPI0>,  <&cmu CLK_DIV_SPI0_PRE>, <&cmu CLK_SCLK_SPI0>;
+	assigned-clock-parents = <&cmu CLK_FOUT_MPLL>, <&cmu CLK_MOUT_MPLL>,    <&cmu CLK_DIV_MPLL_PRE>, <&cmu CLK_MOUT_SPI0>, <&cmu CLK_DIV_SPI0>,     <&cmu CLK_DIV_SPI0_PRE>;
+
+	ax88796c@0 {
+		compatible = "asix,ax88796c";
+		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a boot-loader */
+		interrupt-parent = <&gpx2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <40000000>;
+		reg = <0x0>;
+		reset-gpios = <&gpe0 2 GPIO_ACTIVE_LOW>;
+		controller-data {
+			samsung,spi-feedback-delay = <2>;
+		};
+	};
+};
-- 
2.26.2
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help