On 24/08/16 14:37, Mirza Krak wrote:
quoted hunk ↗ jump to hunk
From: Mirza Krak <redacted>
Document the devicetree bindings for the Generic Memory Interface (GMI)
bus driver found on Tegra SOCs.
Signed-off-by: Mirza Krak <redacted>
---
Changes in v2:
- Updated examples and some information based on comments from Jon Hunter.
.../devicetree/bindings/bus/nvidia,tegra20-gmi.txt | 132 +++++++++++++++++++++
1 file changed, 132 insertions(+)
create mode 100644 Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
new file mode 100644
index 0000000..8c1e15f
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
@@ -0,0 +1,132 @@
+Device tree bindings for NVIDIA Tegra Generic Memory Interface bus
+
+The Generic Memory Interface bus enables memory transfers between internal and
+external memory. Can be used to attach various high speed devices such as
+synchronous/asynchronous NOR, FPGA, UARTS and more.
+
+The actual devices are instantiated from the child nodes of a GMI node.
+
+Required properties:
+ - compatible : Should contain one of the following:
+ For Tegra20 must contain "nvidia,tegra20-gmi".
+ For Tegra30 must contain "nvidia,tegra30-gmi".
+ - reg: Should contain GMI controller registers location and length.
+ - clocks: Must contain an entry for each entry in clock-names.
+ - clock-names: Must include the following entries: "gmi"
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "gmi"
+ - #address-cells: The number of cells used to represent physical base
+ addresses in the GMI address space. Should be 1.
+ - #size-cells: The number of cells used to represent the size of an address
+ range in the GMI address space. Should be 1.
+ - ranges: Must be set up to reflect the memory layout with three integer values
+ for each chip-select line in use (only one entry is supported, see below
+ comments):
+ <cs-number> <physical address of mapping> <size>
+
+Note that the GMI controller does not have any internal chip-select address
+decoding, because of that chip-selects either need to be managed via software
+or by employing external chip-select decoding logic.
+
+If external chip-select logic is used to support multiple devices it is assumed
+that the devices use the same timing and so are probably the same type. It also
+assumes that they can fit in the 256MB address range. In this case only one
+child device is supported which represents the active chip-select line, see
+examples for more insight.
+
+Required child cs node properties:
+ - reg: First entry should contain the active chip-select number
+
+Optional child cs node properties:
+
+ - nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit.
+ - nvidia,snor-mux-mode: Enable address/data MUX mode.
+ - nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data.
+ If omitted it will be asserted with data.
+ - nvidia,snor-rdy-inv: RDY signal is active high
+ - nvidia,snor-adv-inv: ADV signal is active high
+ - nvidia,snor-oe-inv: WE/OE signal is active high
+ - nvidia,snor-cs-inv: CS signal is active high
+
+ Note that there is some special handling for the timing values.
+ From Tegra TRM:
+ Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 1
+
+ - nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the
+ bus. Valid values are 0-15, default is 1
+ - nvidia,snor-hold-width: Number of cycles CE stays asserted after the
+ de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N
+ (in case of MASTER Request). Valid values are 0-15, default is 1
+ - nvidia,snor-adv-width: Number of cycles during which ADV stays asserted.
+ Valid values are 0-15, default is 1.
+ - nvidia,snor-ce-width: Number of cycles before CE is asserted.
+ Valid values are 0-15, default is 4
+ - nvidia,snor-we-width: Number of cycles during which WE stays asserted.
+ Valid values are 0-15, default is 1
+ - nvidia,snor-oe-width: Number of cycles during which OE stays asserted.
+ Valid values are 0-255, default is 1
+ - nvidia,snor-wait-width: Number of cycles before READY is asserted.
+ Valid values are 0-255, default is 3
+
+Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the
+controllers with a simple-bus node since they are all connected to the same
+chip-select (CS4), in this example external address decoding is provided:
+
+gmi@70090000 {
+ compatible = "nvidia,tegra20-gmi";
+ reg = <0x70009000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&tegra_car TEGRA20_CLK_NOR>;
+ clock-names = "gmi";
+ resets = <&tegra_car 42>;
+ reset-names = "gmi";
+ ranges = <4 0x48000000 0x7ffffff>;
+
+ status = "disabled";
+
+ bus@4 {
+ compatible = "simple-bus";
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 4 0x40100>;
Does this work? I tried to add an example like this and I got ...
Warning (reg_format): "reg" property in /gmi@70009000/bus@4 has invalid
length (4 bytes) (#address-cells == 1, #size-cells == 1)
I am wondering if we should just following the arm,pl172 example and
have ...
cs4 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
nvidia,snor-cs = <4>;
nvidia,snor-mux-mode;
nvidia,snor-adv-inv;
can@0 {
reg = <0 0x100>;
...
};
...
};
Cheers
Jon
--
nvpublic