[PATCH 4/4] pinctrl: remove bindings for pinconf options needing more thought
From: Heiko Stübner <heiko@sntech.de>
Date: 2013-06-25 12:57:15
Also in:
lkml
Subsystem:
open firmware and flattened device tree bindings, pin control subsystem, the rest · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Walleij, Linus Torvalds
Some options currently take arguments in unspecified driver-specific units. As pointed out by Stephen Warren, driver specific values should not be part of generic devicetree bindings describing the hardware. Therefore remove the critical bindings again, before they become part of an official release. Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../devicetree/bindings/pinctrl/pinctrl-bindings.txt | 10 ---------- drivers/pinctrl/pinconf-generic.c | 3 --- 2 files changed, 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index 788ab09..aeb3c99 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt@@ -154,10 +154,7 @@ drive-open-source - drive with open source drive-strength - sink or source at most X mA input-schmitt-enable - enable schmitt-trigger mode input-schmitt-disable - disable schmitt-trigger mode -input-schmitt - run in schmitt-trigger mode with hysteresis X input-debounce - debounce mode with debound time X -power-source - select power source X -slew-rate - use slew-rate X low-power-enable - enable low power mode low-power-disable - disable low power mode output-low - set the pin to output mode with low level
@@ -170,16 +167,9 @@ Arguments for parameters: - drive-strength takes as argument the target strength in mA. -- input-schmitt takes as argument the adjustable hysteresis in a - driver-specific format - - input-debounce takes the debounce time in usec as argument or 0 to disable debouncing -- power-source argument is the custom value describing the source to select - -- slew-rate takes as argument the target rate in a driver-specific format - All parameters not listed here, do not take an argument. More in-depth documentation on these parameters can be found in
diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index 2b271d5..8594f03 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c@@ -161,10 +161,7 @@ static struct pinconf_generic_dt_params dt_params[] = { { "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 }, { "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 }, { "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 }, - { "input-schmitt", PIN_CONFIG_INPUT_SCHMITT, 0 }, { "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 }, - { "power-source", PIN_CONFIG_POWER_SOURCE, 0 }, - { "slew-rate", PIN_CONFIG_SLEW_RATE, 0 }, { "low-power-enable", PIN_CONFIG_LOW_POWER_MODE, 1 }, { "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 }, { "output-low", PIN_CONFIG_OUTPUT, 0, },
--
1.7.10.4