On 18/11/2020 17:12, Nishanth Menon wrote:

On 13:38-20201118, Grygorii Strashko wrote:

quoted

Hi Rob,

On 17/11/2020 18:19, Sekhar Nori wrote:

quoted

With dtc 1.6.0, building TI device-tree files with W=2 results in warnings
like below for all interrupt controllers.

/bus@100000/bus@30000000/interrupt-controller1: Missing #address-cells in interrupt provider

Fix these by adding #address-cells = <0>; for all interrupt controllers in
TI device-tree files. Any other #address-cells value is really only needed
if interrupt-map property is being used (which is not the case for existing
TI device-tree files)

Signed-off-by: Sekhar Nori <redacted>
---
   arch/arm64/boot/dts/ti/k3-am65-main.dtsi              |  5 +++++
   arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi            |  2 ++
   arch/arm64/boot/dts/ti/k3-am654-base-board.dts        |  1 +
   arch/arm64/boot/dts/ti/k3-j7200-main.dtsi             |  3 +++
   arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi       |  1 +
   arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts |  1 +
   arch/arm64/boot/dts/ti/k3-j721e-main.dtsi             | 11 +++++++++++
   arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi       |  3 +++
   8 files changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index aa8725db0187..55aaa1404d7d 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi

@@ -440,6 +440,7 @@
   		interrupt-controller;
   		interrupt-parent = <&gic500>;
   		#interrupt-cells = <1>;
+		#address-cells = <0>;

Does it really required or mandatory to have #address-cells = <0>; defined for interrupt-controller DT nodes which
do not have child nodes and no "interrupt-map"?

Just to help clarify (I could be mistaken as well): is'nt the
interrupt map for user interrupt map nodes that refer to this
interrupt controller node to state they dont need a parent address
specifier - so are we claiming none of the users will have an
interrupt-map (now and never in the future as well) - we we might want
to explain why we think that is the case, and if we are expecting dtc
to deduce that (if so how?)?

The main reason I commented - is hope to get some clarification from DT maintainers.
90% of interrupt-controller nodes do not have #address-cells and I never seen in in GPIO nodes
(most often is present in PCI and GIC nodes).
and nobody seems fixing it. So, if we are going to move this direction it's reasonable to get clarification to be sure.

And there is no "never" here - #address-cells always can be added if really required.

-- 
Best regards,
grygorii

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel