[PATCH v3 09/10] ARM: dts: omap3-beagle-xm: Add USB Host support

Nishant,

On 11/19/2013 11:05 PM, Nishanth Menon wrote:

On 09/24/2013 03:53 AM, Roger Quadros wrote:

quoted

Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.

We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.

Signed-off-by: Roger Quadros <redacted>
---

just using this thread, but a question ->

I am kernel * master                                   dec8e46 Merge
tag 'arc-v3.13-rc1-part2' of
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc

and I see that VAUX2 which supplies USB_1V8[1] is not enabled -> I did
a quick patch and it did seem to work (Usb keyboard, networking, mouse
etc on my ehci ports seems to come up good) - any suggestions how we'd
like to handle this?

It worked for me without your patch. It could be that u-boot is enabling
that regulator for me. I'm on u-boot-v2013.10.

In any case, your patch seems the right thing to do. We should take it in
the rc cycle.

cheers,
-roger

quoted

 arch/arm/boot/dts/omap3-beagle-xm.dts |   65 ++++++++++++++++++++++++++++-----
 1 files changed, 56 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index afdb164..b081f5a 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -69,6 +69,23 @@
 		};
 
 	};
+
+	/* HS USB Port 2 Power */
+	hsusb2_power: hsusb2_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&twl_gpio 18 0>;	/* GPIO LEDA */
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
+		vcc-supply = <&hsusb2_power>;
+	};
 };
 
 &omap3_pmx_wkup {

@@ -79,6 +96,37 @@
 	};
 };
 
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusbb2_pins
+	>;
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+		>;
+	};
+
+	hsusbb2_pins: pinmux_hsusbb2_pins {
+		pinctrl-single,pins = <
+			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <2600000>;
 

@@ -148,15 +196,6 @@
 	power = <50>;
 };
 
-&omap3_pmx_core {
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
-		>;
-	};
-};
-
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;

@@ -166,3 +205,11 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio1_pins>;
 };
+
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};