[PATCH v3 09/10] ARM: dts: omap3-beagle-xm: Add USB Host support
From: Roger Quadros <hidden>
Date: 2013-09-24 08:54:57
Also in:
linux-devicetree, linux-omap, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
Provide RESET GPIO and Power regulator for the USB PHY, the USB Host port mode and the PHY device for the controller. Also provide pin multiplexer information for USB host pins. We also relocate omap3_pmx_core pin definations so that they are close to omap3_pmx_wkup pin definations. Signed-off-by: Roger Quadros <redacted> --- arch/arm/boot/dts/omap3-beagle-xm.dts | 65 ++++++++++++++++++++++++++++----- 1 files changed, 56 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index afdb164..b081f5a 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts@@ -69,6 +69,23 @@ }; }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */ + vcc-supply = <&hsusb2_power>; + }; }; &omap3_pmx_wkup {
@@ -79,6 +96,37 @@ }; }; +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb2_pins + >; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ + >; + }; + + hsusbb2_pins: pinmux_hsusbb2_pins { + pinctrl-single,pins = < + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; +}; + &i2c1 { clock-frequency = <2600000>;
@@ -148,15 +196,6 @@ power = <50>; }; -&omap3_pmx_core { - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ - >; - }; -}; - &uart3 { pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>;
@@ -166,3 +205,11 @@ pinctrl-names = "default"; pinctrl-0 = <&gpio1_pins>; }; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +};
--
1.7.4.1