Hi Uwe,
On Thu, Jan 13, 2011 at 03:49:00PM +0100, Uwe Kleine-K?nig wrote:
On Tue, Jan 11, 2011 at 08:09:24PM +0800, Shawn Guo wrote:
quoted
Signed-off-by: Shawn Guo <redacted>
---
Changes for v5:
- Do not use CONFIG_FEC2 which is a fec driver configration
arch/arm/mach-mxs/mach-mx28evk.c | 26 +++++++++++++++++++++++---
1 files changed, 23 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-mxs/mach-mx28evk.c b/arch/arm/mach-mxs/mach-mx28evk.c
index d162e95..8e2c597 100644
--- a/arch/arm/mach-mxs/mach-mx28evk.c
+++ b/arch/arm/mach-mxs/mach-mx28evk.c
@@ -57,6 +57,19 @@ static const iomux_cfg_t mx28evk_pads[] __initconst = {
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_ENET_CLK__CLKCTRL_ENET |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ /* fec1 */
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_ENET0_COL__ENET1_TX_EN |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
/* phy power line */
MX28_PAD_SSP1_DATA3__GPIO_2_15 |
(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),@@ -106,8 +119,14 @@ static void __init mx28evk_fec_reset(void)
gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
}
-static const struct fec_platform_data mx28_fec_pdata __initconst = {
- .phy = PHY_INTERFACE_MODE_RMII,
+static struct fec_platform_data mx28_fec_pdata[] = {
this can still be initdata, doesn't it?
Sascha has merged the patch. This one line change may not deserve
a separate patch, so I will take care of it when updating the file
with new version of ocotp patch.
--
Regards,
Shawn