Signed-off-by: Shawn Guo <redacted>
---
Changes for v5:
 - Do not use CONFIG_FEC2 which is a fec driver configration

 arch/arm/mach-mxs/mach-mx28evk.c |   26 +++++++++++++++++++++++---
 1 files changed, 23 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-mxs/mach-mx28evk.c b/arch/arm/mach-mxs/mach-mx28evk.c
index d162e95..8e2c597 100644
--- a/arch/arm/mach-mxs/mach-mx28evk.c
+++ b/arch/arm/mach-mxs/mach-mx28evk.c

@@ -57,6 +57,19 @@ static const iomux_cfg_t mx28evk_pads[] __initconst = {
 		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
 	MX28_PAD_ENET_CLK__CLKCTRL_ENET |
 		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	/* fec1 */
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_COL__ENET1_TX_EN |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
 	/* phy power line */
 	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
 		(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),

@@ -106,8 +119,14 @@ static void __init mx28evk_fec_reset(void)
 	gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
 }
 
-static const struct fec_platform_data mx28_fec_pdata __initconst = {
-	.phy = PHY_INTERFACE_MODE_RMII,
+static struct fec_platform_data mx28_fec_pdata[] = {

+	{
+		/* fec0 */
+		.phy = PHY_INTERFACE_MODE_RMII,
+	}, {
+		/* fec1 */
+		.phy = PHY_INTERFACE_MODE_RMII,
+	},
 };
 
 static void __init mx28evk_init(void)

@@ -117,7 +136,8 @@ static void __init mx28evk_init(void)
 	mx28_add_duart();
 
 	mx28evk_fec_reset();
-	mx28_add_fec(0, &mx28_fec_pdata);
+	mx28_add_fec(0, &mx28_fec_pdata[0]);
+	mx28_add_fec(1, &mx28_fec_pdata[1]);
 }
 
 static void __init mx28evk_timer_init(void)

-- 
1.7.1