[PATCH net-next v9 04/15] dpll: sit9531x: read DPLL types and pin properties from system firmware

@@ -1,4 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 
 obj-$(CONFIG_SIT9531X_DPLL) += sit9531x.o
-sit9531x-y := core.o
+sit9531x-y := core.o prop.o

@@ -23,7 +23,17 @@
 
 #define SIT9531X_NUM_PLLS		4
 #define SIT9531X_MAX_INPUTS		8
+#define SIT9531X_NUM_INPUT_PAIRS	(SIT9531X_MAX_INPUTS / 2)
 #define SIT9531X_MAX_OUTPUTS		12
+/*
+ * INTSYNC (the inter-PLL sync net) is modeled as two pins.  The
+ * destination PLL that locks to INTSYNC sees an input pin
+ * (SIT9531X_INTSYNC_PIN_ID, in the input id namespace after the physical
+ * inputs and the xtal); the source PLL that drives INTSYNC sees an output
+ * pin (SIT9531X_INTSYNC_OUT_PIN_ID, appended after the physical outputs).
+ */
+#define SIT9531X_INTSYNC_PIN_ID		(SIT9531X_MAX_INPUTS + 1)
+#define SIT9531X_INTSYNC_OUT_PIN_ID	SIT9531X_MAX_OUTPUTS
 
 /*
  * struct sit9531x_chip_info - chip variant identification

@@ -41,6 +51,39 @@ struct sit9531x_chip_info {
 	const u8	*clkout_map;
 };
 
+/*
+ * enum sit9531x_signal_mode - input signal electrical mode
+ * @SIT9531X_MODE_SE: single-ended
+ * @SIT9531X_MODE_DE: differential
+ */
+enum sit9531x_signal_mode {
+	SIT9531X_MODE_SE = 0,
+	SIT9531X_MODE_DE,
+};
+
+/*
+ * struct sit9531x_ref - input reference state
+ * @freq:		configured frequency in Hz
+ * @label:		board label from DT or default
+ * @sig_mode:		signal mode of the pair this lane belongs to
+ *			(detected from CLKINx_INPUT_MODE at probe)
+ */
+struct sit9531x_ref {
+	u32				freq;
+	const char			*label;
+	enum sit9531x_signal_mode	sig_mode;
+};
+
+/*
+ * struct sit9531x_out - output state
+ * @freq:		configured frequency in Hz
+ * @label:		board label from DT or default
+ */
+struct sit9531x_out {
+	u32		freq;
+	const char	*label;
+};
+
 /*
  * struct sit9531x_dev - SiT9531x device instance
  * @dev:		parent device

@@ -48,6 +91,8 @@ struct sit9531x_chip_info {
  * @regmap:		paged register map
  * @info:		detected chip variant info
  * @multiop_lock:	serializes multi-register sequences
+ * @ref:		array of input reference states
+ * @out:		array of output states
  * @xtal_freq:		crystal oscillator frequency in Hz
  * @reset_gpio:		optional reset line (DT "reset-gpios"), NULL if absent
  */

@@ -59,11 +104,38 @@ struct sit9531x_dev {
 	/* Serializes multi-step register sequences */
 	struct mutex			multiop_lock;
 
+	/* Hardware state */
+	struct sit9531x_ref	ref[SIT9531X_MAX_INPUTS + 1]; /* +1 for xtal */
+	struct sit9531x_out	out[SIT9531X_MAX_OUTPUTS];
 	u32			xtal_freq;
 
 	struct gpio_desc	*reset_gpio;
 };
 
+/*
+ * Logical input pins are interleaved: even index = P lane, odd
+ * index = N lane of pair index/2 (IN0P, IN0N, IN1P, IN1N, ...).
+ * Index SIT9531X_MAX_INPUTS is the XO input.
+ */
+
+/*
+ * sit9531x_input_pair - get input pair number for a logical input index
+ * @index: logical input pin index
+ */
+static inline u8 sit9531x_input_pair(u8 index)
+{
+	return index >> 1;
+}
+
+/*
+ * sit9531x_input_is_n - check if a logical input index is an N lane
+ * @index: logical input pin index
+ */
+static inline bool sit9531x_input_is_n(u8 index)
+{
+	return index & 1;
+}
+
 /*
  * sit9531x_pll_page - get register page for PLL index
  * @pll_idx: PLL index (0 = PLLA, 3 = PLLD)

@@ -0,0 +1,437 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SiTime SiT9531x firmware node property parsing
+ *
+ * Copyright (C) 2026 SiTime Corp.
+ * Author: Ali Rouhi <arouhi@sitime.com>
+ * Author: Oleg Zadorozhnyi <Oleg.Zadorozhnyi@devoxsoftware.com>
+ *
+ * Retrieves pin properties from Device Tree firmware nodes (or
+ * applies defaults when no firmware node exists).
+ */
+
+#include <linux/dev_printk.h>
+#include <linux/dpll.h>
+#include <linux/err.h>
+#include <linux/fwnode.h>
+#include <linux/property.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+
+#include "core.h"
+#include "prop.h"
+
+/*
+ * sit9531x_input_pin_label - fill the package label for an input pin
+ *
+ * Split out so input-naming changes stay local to this helper.
+ */
+static void sit9531x_input_pin_label(struct sit9531x_dev *sitdev,
+				     struct sit9531x_pin_props *props, u8 id)
+{
+	u8 pair = sit9531x_input_pair(id);
+
+	if (sitdev->ref[id].sig_mode == SIT9531X_MODE_DE)
+		snprintf(props->package_label,
+			 sizeof(props->package_label), "IN%u", pair);
+	else
+		snprintf(props->package_label,
+			 sizeof(props->package_label), "IN%u%c", pair,
+			 sit9531x_input_is_n(id) ? 'N' : 'P');
+}
+
+/*
+ * sit9531x_prop_pin_package_label_set - generate package label
+ * @dir:	pin direction
+ * @id:		pin index
+ *
+ * Generates a package label string.  Output pins are named "OUT0",
+ * "OUT1", ...  Input pins are named after the physical pair and lane:
+ * "IN0P", "IN0N", "IN1P", ... for single-ended lanes, or "IN0",
+ * "IN1", ... when the pair is configured differential (the N lane is
+ * not registered in that case).
+ */
+static void
+sit9531x_prop_pin_package_label_set(struct sit9531x_dev *sitdev,
+				    struct sit9531x_pin_props *props,
+				    enum dpll_pin_direction dir, u8 id)
+{
+	/* The internal INTSYNC pin has a fixed label */
+	if (dir == DPLL_PIN_DIRECTION_INPUT &&
+	    id == SIT9531X_INTSYNC_PIN_ID) {
+		strscpy(props->package_label, "INTSYNC",
+			sizeof(props->package_label));
+		props->dpll_props.package_label = props->package_label;
+		return;
+	}
+
+	/* The internal XO reference has a fixed label */
+	if (dir == DPLL_PIN_DIRECTION_INPUT && id == SIT9531X_MAX_INPUTS) {
+		strscpy(props->package_label, "XO",
+			sizeof(props->package_label));
+		props->dpll_props.package_label = props->package_label;
+		return;
+	}
+
+	/* The internal INTSYNC source (output) pin has a fixed label */
+	if (dir == DPLL_PIN_DIRECTION_OUTPUT &&
+	    id == SIT9531X_INTSYNC_OUT_PIN_ID) {
+		strscpy(props->package_label, "SYNCOUT",
+			sizeof(props->package_label));
+		props->dpll_props.package_label = props->package_label;
+		return;
+	}
+
+	if (dir == DPLL_PIN_DIRECTION_INPUT)
+		sit9531x_input_pin_label(sitdev, props, id);
+	else
+		snprintf(props->package_label, sizeof(props->package_label),
+			 "OUT%u", id);
+
+	props->dpll_props.package_label = props->package_label;
+}
+
+/*
+ * sit9531x_prop_pin_fwnode_get - find firmware node for a pin
+ * @dir:	pin direction
+ * @id:		pin index
+ *
+ * Searches for input-pins/output-pins child nodes in DT, looking
+ * for a child whose "reg" property matches @id.
+ *
+ * Return: 0 on success, -ENOENT if no firmware node exists
+ */
+static int
+sit9531x_prop_pin_fwnode_get(struct sit9531x_dev *sitdev,
+			     struct sit9531x_pin_props *props,
+			     enum dpll_pin_direction dir, u8 id)
+{
+	struct fwnode_handle *pins_node, *pin_node;
+	const char *node_name;
+
+	if (dir == DPLL_PIN_DIRECTION_INPUT)
+		node_name = "input-pins";
+	else
+		node_name = "output-pins";
+
+	pins_node = device_get_named_child_node(sitdev->dev, node_name);
+	if (!pins_node) {
+		dev_dbg(sitdev->dev, "'%s' sub-node is missing\n", node_name);
+		return -ENOENT;
+	}
+
+	/* Enumerate child pin nodes and find the requested one */
+	fwnode_for_each_child_node(pins_node, pin_node) {
+		u32 reg;
+
+		if (fwnode_property_read_u32(pin_node, "reg", &reg))
+			continue;
+
+		if (id == reg)
+			break;
+	}
+
+	fwnode_handle_put(pins_node);
+
+	props->fwnode = pin_node;
+
+	dev_dbg(sitdev->dev, "Firmware node for %s %sfound\n",
+		props->package_label, pin_node ? "" : "NOT ");
+
+	return pin_node ? 0 : -ENOENT;
+}
+
+/*
+ * sit9531x_pin_props_get - get pin properties for a given pin
+ * @dir:	pin direction (INPUT or OUTPUT)
+ * @index:	pin index
+ *
+ * Allocates a pin properties structure, generates a package label,
+ * looks up the firmware node if available, and reads optional
+ * properties (label, connection-type, supported-frequencies-hz,
+ * esync-control).
+ *
+ * Call sit9531x_pin_props_put() to free the returned structure.
+ *
+ * Return: pointer to pin properties on success, error pointer on error
+ */
+struct sit9531x_pin_props *
+sit9531x_pin_props_get(struct sit9531x_dev *sitdev,
+		       enum dpll_pin_direction dir, u8 index)
+{
+	struct dpll_pin_frequency *ranges;
+	struct sit9531x_pin_props *props;
+	int i, j, num_freqs = 0, rc;
+	u64 *freqs = NULL;
+	const char *type;
+	u64 curr_freq;
+
+	props = kzalloc_obj(*props, GFP_KERNEL);
+	if (!props)
+		return ERR_PTR(-ENOMEM);
+
+	if (dir == DPLL_PIN_DIRECTION_INPUT &&
+	    index == SIT9531X_INTSYNC_PIN_ID) {
+		/*
+		 * INTSYNC destination pin: a PLL locks to the INTSYNC net as a
+		 * reference, so it can be connected and re-prioritised.
+		 */
+		props->dpll_props.type = DPLL_PIN_TYPE_INT_OSCILLATOR;
+		props->dpll_props.capabilities =
+			DPLL_PIN_CAPABILITIES_PRIORITY_CAN_CHANGE |
+			DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE;
+		curr_freq = 0;
+	} else if (dir == DPLL_PIN_DIRECTION_OUTPUT &&
+		   index == SIT9531X_INTSYNC_OUT_PIN_ID) {
+		/*
+		 * INTSYNC source pin: a PLL drives the INTSYNC net.  It can be
+		 * connected/disconnected but carries no priority (driving the
+		 * net is not a reference selection) and no frequency.
+		 */
+		props->dpll_props.type = DPLL_PIN_TYPE_INT_OSCILLATOR;
+		props->dpll_props.capabilities =
+			DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE;
+		curr_freq = 0;
+	} else if (dir == DPLL_PIN_DIRECTION_INPUT &&
+		   index == SIT9531X_MAX_INPUTS) {
+		/* The XO reference is fixed: no state or priority control. */
+		props->dpll_props.type = DPLL_PIN_TYPE_INT_OSCILLATOR;
+		props->dpll_props.capabilities = 0;
+		sitdev->ref[index].freq = sitdev->xtal_freq;
+		curr_freq = sitdev->xtal_freq;
+	} else if (dir == DPLL_PIN_DIRECTION_INPUT) {
+		props->dpll_props.type = DPLL_PIN_TYPE_EXT;
+		props->dpll_props.capabilities =
+			DPLL_PIN_CAPABILITIES_PRIORITY_CAN_CHANGE |
+			DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE;
+		curr_freq = sitdev->ref[index].freq;
+	} else {
+		/*
+		 * A synthesized clock output is an external connection with
+		 * no more specific meaning; a board that knows better says
+		 * so through the pin's connection-type property below.
+		 */
+		props->dpll_props.type = DPLL_PIN_TYPE_EXT;
+		props->dpll_props.capabilities =
+			DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE;
+		curr_freq = sitdev->out[index].freq;
+
+		/*
+		 * Allow phase-adjust over a +/-1 ms window.  The subsystem
+		 * rejects pin_set(phase-adjust, X) when X falls outside
+		 * [min, max], so leaving these at 0 silently blocks every
+		 * netlink call.  1 ms is well beyond the DCO dynamic range
+		 * but costs nothing.  Only outputs get a range: input pins
+		 * have no .phase_adjust_set, and advertising one there would
+		 * promise userspace something every set would refuse.
+		 */
+		props->dpll_props.phase_range.min = -1000000000; /* -1 ms in ps */
+		props->dpll_props.phase_range.max =  1000000000; /* +1 ms in ps */
+		/*
+		 * The fine step is 30 ps, but requests are accepted at 1 ps
+		 * resolution and rounded to the nearest achievable delay, so
+		 * advertise the request granularity, not the hardware step.
+		 */
+		props->dpll_props.phase_gran = 1;
+	}
+
+	/* Generate package label */
+	sit9531x_prop_pin_package_label_set(sitdev, props, dir, index);
+
+	/*
+	 * Both INTSYNC pins are internal to the chip and have no board-level
+	 * wiring, so they take no properties from the firmware node.
+	 */
+	if (dir == DPLL_PIN_DIRECTION_INPUT &&
+	    (index == SIT9531X_INTSYNC_PIN_ID ||
+	     index == SIT9531X_MAX_INPUTS))
+		goto skip_fwnode_props;
+	if (dir == DPLL_PIN_DIRECTION_OUTPUT &&
+	    index == SIT9531X_INTSYNC_OUT_PIN_ID)
+		goto skip_fwnode_props;
+
+	rc = sit9531x_prop_pin_fwnode_get(sitdev, props, dir, index);
+	if (rc)
+		goto skip_fwnode_props;
+
+	/* Look for "label" property -> board label */
+	fwnode_property_read_string(props->fwnode, "label",
+				    &props->dpll_props.board_label);
+
+	/* Look for "connection-type" property -> pin type enum */
+	if (!fwnode_property_read_string(props->fwnode, "connection-type",
+					 &type)) {
+		if (!strcmp(type, "ext"))
+			props->dpll_props.type = DPLL_PIN_TYPE_EXT;
+		else if (!strcmp(type, "gnss"))
+			props->dpll_props.type = DPLL_PIN_TYPE_GNSS;
+		else if (!strcmp(type, "int"))
+			props->dpll_props.type = DPLL_PIN_TYPE_INT_OSCILLATOR;
+		else if (!strcmp(type, "synce"))
+			props->dpll_props.type = DPLL_PIN_TYPE_SYNCE_ETH_PORT;
+		else if (!strcmp(type, "mux"))
+			props->dpll_props.type = DPLL_PIN_TYPE_MUX;
+		else
+			dev_warn(sitdev->dev,
+				 "Unknown pin type '%s'\n", type);
+	}
+
+	props->esync_control =
+		fwnode_property_read_bool(props->fwnode, "esync-control");
+
+	num_freqs = fwnode_property_count_u64(props->fwnode,
+					      "supported-frequencies-hz");
+	if (num_freqs <= 0) {
+		num_freqs = 0;
+		goto skip_fwnode_props;
+	}
+
+	freqs = kcalloc(num_freqs, sizeof(*freqs), GFP_KERNEL);
+	if (!freqs) {
+		rc = -ENOMEM;
+		goto err_alloc_freqs;
+	}
+
+	rc = fwnode_property_read_u64_array(props->fwnode,
+					    "supported-frequencies-hz",
+					    freqs, num_freqs);
+	if (rc) {
+		dev_warn(sitdev->dev,
+			 "failed to parse supported-frequencies-hz for %s: %d\n",
+			 props->package_label, rc);
+		goto err_alloc_ranges;
+	}
+
+	/*
+	 * Seed the runtime ref->freq / out->freq with the first DT-listed
+	 * supported frequency so the netlink frequency_get callback reports
+	 * a sane initial value before any pin_set occurs.  DT lists the
+	 * physically-wired reference frequency for each input pin and the
+	 * default output frequency for each output pin.
+	 */
+	if (num_freqs > 0) {
+		if (dir != DPLL_PIN_DIRECTION_INPUT ||
+		    index != SIT9531X_MAX_INPUTS)
+			curr_freq = freqs[0];
+	}
+
+skip_fwnode_props:
+	/* Neither INTSYNC pin carries a frequency attribute */
+	if (dir == DPLL_PIN_DIRECTION_INPUT &&
+	    index == SIT9531X_INTSYNC_PIN_ID)
+		return props;
+	if (dir == DPLL_PIN_DIRECTION_OUTPUT &&
+	    index == SIT9531X_INTSYNC_OUT_PIN_ID)
+		return props;
+
+	/*
+	 * Advertise only concrete values from firmware plus current runtime
+	 * value. For outputs without a firmware list, publish one wide range as
+	 * an explicit fallback because those pins do support frequency_set.
+	 */
+	ranges = kcalloc(num_freqs + 2, sizeof(*ranges), GFP_KERNEL);
+	if (!ranges) {
+		rc = -ENOMEM;
+		goto err_alloc_ranges;
+	}
+
+	/*
+	 * Publish the seeded rate only once the pin is certain to be built.
+	 * The allocation above is the last thing that can fail, and a call
+	 * that reports failure must not leave the device's cached rate
+	 * changed behind it.
+	 */
+	if (curr_freq) {
+		if (dir == DPLL_PIN_DIRECTION_INPUT)
+			sitdev->ref[index].freq = curr_freq;
+		else
+			sitdev->out[index].freq = curr_freq;
+	}
+
+	j = 0;
+
+	/* Current frequency first, when known. */
+	if (curr_freq)
+		ranges[j++] = (struct dpll_pin_frequency)DPLL_PIN_FREQUENCY(curr_freq);
+
+	for (i = 0; i < num_freqs; i++) {
+		struct dpll_pin_frequency freq = DPLL_PIN_FREQUENCY(freqs[i]);
+
+		if (freqs[i] == curr_freq)
+			continue;
+		ranges[j++] = freq;
+	}
+
+	if (dir == DPLL_PIN_DIRECTION_OUTPUT && num_freqs == 0) {
+		ranges[j].min = 1;
+		ranges[j].max = 1000000000ULL; /* 1 GHz */
+		j++;
+	}
+
+	if (j > 0) {
+		props->dpll_props.freq_supported = ranges;
+		props->dpll_props.freq_supported_num = j;
+	} else {
+		kfree(ranges);
+		props->dpll_props.freq_supported = NULL;
+		props->dpll_props.freq_supported_num = 0;
+	}
+
+	kfree(freqs);
+
+	return props;
+
+err_alloc_ranges:
+	kfree(freqs);
+err_alloc_freqs:
+	fwnode_handle_put(props->fwnode);
+	kfree(props);
+
+	return ERR_PTR(rc);
+}
+
+/*
+ * sit9531x_pin_props_put - release pin properties
+ * @props:	pin properties to free
+ */
+void sit9531x_pin_props_put(struct sit9531x_pin_props *props)
+{
+	kfree(props->dpll_props.freq_supported);
+
+	if (props->fwnode)
+		fwnode_handle_put(props->fwnode);
+
+	kfree(props);
+}
+
+/*
+ * sit9531x_prop_dpll_type_get - get DPLL channel type from firmware
+ * @index:	DPLL channel index (0-3)
+ *
+ * Reads the "dpll-types" string array property from the firmware node
+ * and returns the corresponding DPLL type enum.
+ *
+ * Return: DPLL type for the given channel (default: DPLL_TYPE_PPS)
+ */
+enum dpll_type
+sit9531x_prop_dpll_type_get(struct sit9531x_dev *sitdev, u8 index)
+{
+	const char *types[SIT9531X_NUM_PLLS];
+	int count;
+
+	count = device_property_read_string_array(sitdev->dev, "dpll-types",
+						  types, ARRAY_SIZE(types));
+
+	if (index >= count)
+		return DPLL_TYPE_PPS;
+
+	if (!strcmp(types[index], "pps"))
+		return DPLL_TYPE_PPS;
+	else if (!strcmp(types[index], "eec"))
+		return DPLL_TYPE_EEC;
+
+	dev_warn(sitdev->dev, "Unknown DPLL type '%s', using default\n",
+		 types[index]);
+
+	return DPLL_TYPE_PPS;
+}

@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * SiTime SiT9531x firmware node property parsing
+ *
+ * Copyright (C) 2026 SiTime Corp.
+ * Author: Ali Rouhi <arouhi@sitime.com>
+ * Author: Oleg Zadorozhnyi <Oleg.Zadorozhnyi@devoxsoftware.com>
+ */
+
+#ifndef _SIT9531X_PROP_H
+#define _SIT9531X_PROP_H
+
+#include <linux/dpll.h>
+#include <linux/fwnode.h>
+
+struct sit9531x_dev;
+
+/*
+ * struct sit9531x_pin_props - pin properties from firmware
+ * @fwnode:		firmware node handle (NULL if no DT node)
+ * @dpll_props:		DPLL core pin properties
+ * @package_label:	pin package label (e.g. "IN0", "OUT3")
+ * @esync_control:	embedded sync is controllable
+ */
+struct sit9531x_pin_props {
+	struct fwnode_handle		*fwnode;
+	struct dpll_pin_properties	dpll_props;
+	char				package_label[8];
+	bool				esync_control;
+};
+
+enum dpll_type sit9531x_prop_dpll_type_get(struct sit9531x_dev *sitdev,
+					   u8 index);
+struct sit9531x_pin_props *sit9531x_pin_props_get(struct sit9531x_dev *sitdev,
+						  enum dpll_pin_direction dir,
+						  u8 index);
+void sit9531x_pin_props_put(struct sit9531x_pin_props *props);
+
+#endif /* _SIT9531X_PROP_H */