On 12/05/2023 13:28, Ivan Mikhaylov wrote:
On Fri, 2023-05-12 at 08:22 +0200, Krzysztof Kozlowski wrote:
quoted
On 11/05/2023 01:31, Ivan Mikhaylov wrote:
quoted
On Wed, 2023-05-10 at 16:48 +0200, Krzysztof Kozlowski wrote:
quoted
On 09/05/2023 16:35, Ivan Mikhaylov wrote:
quoted
Add the mac-address-increment option for specify MAC address
taken
by
any other sources.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Ivan Mikhaylov <redacted>
---
.../devicetree/bindings/net/ethernet-controller.yaml | 8
++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/ethernet-
controller.yaml
b/Documentation/devicetree/bindings/net/ethernet-
controller.yaml
index 00be387984ac..6900098c5105 100644
--- a/Documentation/devicetree/bindings/net/ethernet-
controller.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-
controller.yaml
@@ -34,6 +34,14 @@ properties:
minItems: 6
maxItems: 6
+ mac-address-increment:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ Specifies the MAC address increment to be added to the
MAC
address.
+ Should be used in cases when there is a need to use MAC
address
+ different from one obtained by any other level, like u-
boot
or the
+ NC-SI stack.
We don't store MAC addresses in DT, but provide simple
placeholder
for
firmware or bootloader. Why shall we store static "increment"
part of
MAC address? Can't the firmware give you proper MAC address?
Best regards,
Krzysztof
Krzysztof, maybe that's a point to make commit message with better
explanation from my side. At current time there is at least two
cases
where I see it's possible to be used:
1. NC-SI
2. embedded
At NC-SI level there is Get Mac Address command which provides to
BMC
mac address from the host which is same as host mac address, it
happens
at runtime and overrides old one.
Also, this part was also to be discussed 2 years ago in this
thread:
https://lore.kernel.org/all/OF8E108F72.39D22E89-ON00258765.001E46EB-00258765.00251157@ibm.com/ (local)
Which was not sent to Rob though...
quoted
Where Milton provided this information:
DTMF spec DSP0222 NC-SI (network controller sideband interface)
is a method to provide a BMC (Baseboard management controller)
shared
access to an external ethernet port for comunication to the
management
network in the outside world. The protocol describes ethernet
packets
that control selective bridging implemented in a host network
controller
to share its phy. Various NIC OEMs have added a query to find out
the
address the host is using, and some vendors have added code to
query
host
nic and set the BMC mac to a fixed offset (current hard coded +1
from
the host value). If this is compiled in the kernel, the NIC OEM is
recognised and the BMC doesn't miss the NIC response the address is
set
once each time the NCSI stack reinitializes. This mechanism
overrides
any mac-address or local-mac-address or other assignment.
DSP0222
https://www.dmtf.org/documents/pmci/network-controller-sideband-interface-nc-si-specification-110
In embedded case, sometimes you have different multiple ethernet
interfaces which using one mac address which increments or
decrements
for particular interface, just for better explanation, there is
patch
with explanation which providing them such way of work:
https://github.com/openwrt/openwrt/blob/master/target/linux/generic/pending-5.15/682-of_net-add-mac-address-increment-support.patch
In their rep a lot of dts using such option.
None of these explain why this is property of the hardware. I
understand
that this is something you want Linux to do, but DT is not for that
purpose. Do not encode system policies into DT and what above commit
says is a policy.
Krzysztof, okay then to which DT subsystem it should belong? To
ftgmac100 after conversion?
To my understanding, decision to add some numbers to MAC address does
not look like DT property at all. Otherwise please help me to understand
- why different boards with same device should have different offset/value?
Anyway, commit msg also lacks any justification for this.
Best regards,
Krzysztof