[PATCH 1/2] net: mt7531: only do PLL once after the reset

Subsystems: mediatek switch driver, networking drivers, networking [dsa], the rest

STALE1440d

3 messages, 2 authors, 2022-08-23 · open the first message on its own page

[PATCH 1/2] net: mt7531: only do PLL once after the reset

From: Alexander Couzens <lynxis@fe80.eu>
Date: 2022-08-20 22:00:23

Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).

Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
---
 drivers/net/dsa/mt7530.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 835807911be0..95a57aeb466e 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c

@@ -506,14 +506,19 @@ static bool mt7531_dual_sgmii_supported(struct mt7530_priv *priv)
 static int
 mt7531_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
 {
-	struct mt7530_priv *priv = ds->priv;
+	return 0;
+}
+
+static void
+mt7531_pll_setup(struct mt7530_priv *priv)
+{
 	u32 top_sig;
 	u32 hwstrap;
 	u32 xtal;
 	u32 val;
 
 	if (mt7531_dual_sgmii_supported(priv))
-		return 0;
+		return;
 
 	val = mt7530_read(priv, MT7531_CREV);
 	top_sig = mt7530_read(priv, MT7531_TOP_SIG_SR);

@@ -592,8 +597,6 @@ mt7531_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
 	val |= EN_COREPLL;
 	mt7530_write(priv, MT7531_PLLGP_EN, val);
 	usleep_range(25, 35);
-
-	return 0;
 }
 
 static void

@@ -2331,6 +2334,8 @@ mt7531_setup(struct dsa_switch *ds)
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
 		     SYS_CTRL_REG_RST);
 
+	mt7531_pll_setup(priv);
+
 	if (mt7531_dual_sgmii_supported(priv)) {
 		priv->p5_intf_sel = P5_INTF_SEL_GMAC5_SGMII;

@@ -2887,8 +2892,6 @@ mt7531_cpu_port_config(struct dsa_switch *ds, int port)
 	case 6:
 		interface = PHY_INTERFACE_MODE_2500BASEX;
 
-		mt7531_pad_setup(ds, interface);
-
 		priv->p6_interface = interface;
 		break;
 	default:

-- 
2.35.1

[PATCH 2/2] net: mt7531: ensure all MACs are powered down before reset

From: Alexander Couzens <lynxis@fe80.eu>
Date: 2022-08-20 22:00:31

The datasheet [1] explicit describes it as requirement for a reset.

[1] MT7531 Reference Manual for Development Board rev 1.0, page 735

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
---
 drivers/net/dsa/mt7530.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 95a57aeb466e..409d5c3d76ea 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c

@@ -2329,6 +2329,10 @@ mt7531_setup(struct dsa_switch *ds)
 		return -ENODEV;
 	}
 
+	/* all MACs must be forced link-down before sw reset */
+	for (i = 0; i < MT7530_NUM_PORTS; i++)
+		mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
+
 	/* Reset the switch through internal reset */
 	mt7530_write(priv, MT7530_SYS_CTRL,
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |

-- 
2.35.1

Re: [PATCH 1/2] net: mt7531: only do PLL once after the reset

From: Paolo Abeni <pabeni@redhat.com>
Date: 2022-08-23 14:06:06

On Sat, 2022-08-20 at 23:37 +0200, Alexander Couzens wrote:

Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).

Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

This (and the next patch) looks like a fix suitable for -net. Could you
please re-post, targeting the appropriate tree and more importantly
including a 'Fixes' tag in the commit message of each patch?

Thanks!

Paolo

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help