Re: [PATCH] phy: maxlinear: add Maxlinear GPY115/21x/24x driver

On Tue, Jun 01, 2021 at 05:14:01PM +0000, Liang Xu wrote:

On 2/6/2021 12:55 am, Andrew Lunn wrote:

quoted

This email was sent from outside of MaxLinear.

quoted

quoted

quoted

+     linkmode_mod_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT,
+                      phydev->supported,
+                      ret & MDIO_PMA_NG_EXTABLE_5GBT);
+

Does genphy_c45_pma_read_abilities() do the wrong thing here? What
does it get wrong?

The problem comes from condition "phydev->c45_ids.mmds_present &
MDIO_DEVS_AN".

Our product supports both C22 and C45.

In the real system, we found C22 was used by customers (with indirect
access to C45 registers when necessary).

Then during probe, in API "get_phy_device", it skips reading C45 IDs.

So that genphy_c45_pma_read_abilities skip the supported flag
ETHTOOL_LINK_MODE_Autoneg_BIT.

This sounds like a generic problem, which will affect any PHY which
has both C22 and C45. I wounder if it makes sense to add a helper
function which a PHY driver can call to get the
phydev->c45_ids.mmds_present populated?

I thought to use get_phy_c45_ids in gpy_config_init to populate the 
c45_ids, but this is a static function inside phy_device.c.

Yes, which i said maybe add a helper. Something like this in phy_device.c

int phy_get_c45_ids(struct phy_device *phydev) {

	return get_phy_c45_ids(phydev->mdio.bus, phydev->mdio.addr,
			       phydev->c45_ids);
}

Completely untested. Hopefully you get the idea.

Or maybe in genphy_c45_pma_read_abilities, it reads MII_BMSR register if 
is_c45 not set.

quoted

quoted

quoted

quoted

+static int gpy_read_status(struct phy_device *phydev)
+{
+     int ret;
+
+     ret = genphy_update_link(phydev);
+     if (ret)
+             return ret;
+
+     phydev->speed = SPEED_UNKNOWN;
+     phydev->duplex = DUPLEX_UNKNOWN;
+     phydev->pause = 0;
+     phydev->asym_pause = 0;
+
+     if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) {
+             ret = genphy_c45_read_lpa(phydev);
+             if (ret < 0)
+                     return ret;
+
+             /* Read the link partner's 1G advertisement */
+             ret = phy_read(phydev, MII_STAT1000);
+             if (ret < 0)
+                     return ret;
+             mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret);

can genphy_read_lpa() be used here?

2.5G is not covered in genphy_read_lpa.

If I use genphy_c45_read_lpa first then genphy_read_lpa after, it seems
a bit redundant.

I'm just trying to avoid repeating code which is in helpers. I think
this is the first PHY driver which uses a mixture of C22 and C45 like
this. So it could be the helpers need small modifications to make them
work. We should make those modifications, since your PHY is not likely
to be the only mixed C22 and C45 device.

I agree, this is issue for mixed C22/45 device.

I saw something similar in BRCM driver (bcm84881_read_status) and 
Marvell driver (mv3310_read_status_copper).

They are C45 device and use vendor specific register in MMD to access 
C22 equivalent registers.

As you said, those drivers use vendor specific registers.  In your
case, you use standard registers. So that is why i'm thinking it
should be possible to use the helpers.

	 Andrew