[PATCH v7 net-next 00/15] net: mvpp2: Add TX Flow Control support

@@ -69,6 +69,8 @@
 			status = "disabled";
 			dma-coherent;
 
+			cm3-mem = <&CP11X_LABEL(cm3_sram)>;
+
 			CP11X_LABEL(eth0): eth0 {
 				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
 					<43 IRQ_TYPE_LEVEL_HIGH>,

@@ -211,6 +213,14 @@
 			};
 		};
 
+		CP11X_LABEL(cm3_sram): cm3@220000 {
+			compatible = "mmio-sram";
+			reg = <0x220000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x220000 0x800>;
+		};
+
 		CP11X_LABEL(rtc): rtc@284000 {
 			compatible = "marvell,armada-8k-rtc";
 			reg = <0x284000 0x20>, <0x284080 0x24>;

@@ -320,7 +320,7 @@ static int mvpp2_get_nrxqs(struct mvpp2 *priv)
 {
 	unsigned int nrxqs;
 
-	if (priv->hw_version == MVPP22 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
+	if (priv->hw_version != MVPP21 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
 		return 1;
 
 	/* According to the PPv2.2 datasheet and our experiments on

@@ -447,7 +447,7 @@ static void mvpp2_bm_bufs_get_addrs(struct device *dev, struct mvpp2 *priv,
 				      MVPP2_BM_PHY_ALLOC_REG(bm_pool->id));
 	*phys_addr = mvpp2_thread_read(priv, thread, MVPP2_BM_VIRT_ALLOC_REG);
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		u32 val;
 		u32 dma_addr_highbits, phys_addr_highbits;
 

@@ -743,7 +743,7 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 	if (test_bit(thread, &port->priv->lock_map))
 		spin_lock_irqsave(&port->bm_lock[thread], flags);
 
-	if (port->priv->hw_version == MVPP22) {
+	if (port->priv->hw_version != MVPP21) {
 		u32 val = 0;
 
 		if (sizeof(dma_addr_t) == 8)

@@ -1200,7 +1200,7 @@ static bool mvpp2_port_supports_xlg(struct mvpp2_port *port)
 
 static bool mvpp2_port_supports_rgmii(struct mvpp2_port *port)
 {
-	return !(port->priv->hw_version == MVPP22 && port->gop_id == 0);
+	return !(port->priv->hw_version != MVPP21 && port->gop_id == 0);
 }
 
 /* Port configuration routines */

@@ -1818,7 +1818,7 @@ static void mvpp2_mac_reset_assert(struct mvpp2_port *port)
 	      MVPP2_GMAC_PORT_RESET_MASK;
 	writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
 
-	if (port->priv->hw_version == MVPP22 && port->gop_id == 0) {
+	if (port->priv->hw_version != MVPP21 && port->gop_id == 0) {
 		val = readl(port->base + MVPP22_XLG_CTRL0_REG) &
 		      ~MVPP22_XLG_CTRL0_MAC_RESET_DIS;
 		writel(val, port->base + MVPP22_XLG_CTRL0_REG);

@@ -1831,7 +1831,7 @@ static void mvpp22_pcs_reset_assert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);

@@ -1852,7 +1852,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);

@@ -4189,7 +4189,7 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
 	/* Enable interrupts on all threads */
 	mvpp2_interrupts_enable(port);
 
-	if (port->priv->hw_version == MVPP22)
+	if (port->priv->hw_version != MVPP21)
 		mvpp22_mode_reconfigure(port);
 
 	if (port->phylink) {

@@ -4405,7 +4405,7 @@ static int mvpp2_open(struct net_device *dev)
 		valid = true;
 	}
 
-	if (priv->hw_version == MVPP22 && port->port_irq) {
+	if (priv->hw_version != MVPP21 && port->port_irq) {
 		err = request_irq(port->port_irq, mvpp2_port_isr, 0,
 				  dev->name, port);
 		if (err) {

@@ -6053,7 +6053,7 @@ static int mvpp2__mac_prepare(struct phylink_config *config, unsigned int mode,
 			     MVPP2_GMAC_PORT_RESET_MASK,
 			     MVPP2_GMAC_PORT_RESET_MASK);
 
-		if (port->priv->hw_version == MVPP22) {
+		if (port->priv->hw_version != MVPP21) {
 			mvpp22_gop_mask_irq(port);
 
 			phy_power_off(port->comphy);

@@ -6107,7 +6107,7 @@ static int mvpp2_mac_finish(struct phylink_config *config, unsigned int mode,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 
-	if (port->priv->hw_version == MVPP22 &&
+	if (port->priv->hw_version != MVPP21 &&
 	    port->phy_interface != interface) {
 		port->phy_interface = interface;
 

@@ -6787,7 +6787,7 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	if (dram_target_info)
 		mvpp2_conf_mbus_windows(dram_target_info, priv);
 
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		mvpp2_axi_init(priv);
 
 	/* Disable HW PHY polling */

@@ -6950,7 +6950,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
-	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
+	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
 		priv->sysctrl_base =
 			syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
 							"marvell,system-controller");

@@ -6963,7 +6963,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->sysctrl_base = NULL;
 	}
 
-	if (priv->hw_version == MVPP22 &&
+	if (priv->hw_version != MVPP21 &&
 	    mvpp2_get_nrxqs(priv) * 2 <= MVPP2_BM_MAX_POOLS)
 		priv->percpu_pools = 1;
 

@@ -7010,7 +7010,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		if (err < 0)
 			goto err_pp_clk;
 
-		if (priv->hw_version == MVPP22) {
+		if (priv->hw_version != MVPP21) {
 			priv->mg_clk = devm_clk_get(&pdev->dev, "mg_clk");
 			if (IS_ERR(priv->mg_clk)) {
 				err = PTR_ERR(priv->mg_clk);

@@ -7051,7 +7051,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		err = dma_set_mask(&pdev->dev, MVPP2_DESC_DMA_MASK);
 		if (err)
 			goto err_axi_clk;

@@ -7131,10 +7131,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 	clk_disable_unprepare(priv->axi_clk);
 
 err_mg_core_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_core_clk);
 err_mg_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_clk);
 err_gop_clk:
 	clk_disable_unprepare(priv->gop_clk);

@@ -295,6 +295,8 @@
 #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK	0x3fc00000
 #define     MVPP2_PON_CAUSE_MISC_SUM_MASK		BIT(31)
 #define MVPP2_ISR_MISC_CAUSE_REG		0x55b0
+#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)	(0x5520 + 4 * (port))
+#define     MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK	0x00ff
 
 /* Buffer Manager registers */
 #define MVPP2_BM_POOL_BASE_REG(pool)		(0x6000 + ((pool) * 4))

@@ -764,6 +766,7 @@
 #define MSS_SRAM_SIZE		0x800
 #define FC_QUANTA		0xFFFF
 #define FC_CLK_DIVIDER		100
+#define MSS_THRESHOLD_STOP	768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \

@@ -1134,14 +1134,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
 static void mvpp2_interrupts_mask(void *arg)
 {
 	struct mvpp2_port *port = arg;
+	int cpu = smp_processor_id();
+	u32 thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
 }
 
 /* Unmask the current thread's Rx/Tx interrupts.

@@ -1151,20 +1156,25 @@ static void mvpp2_interrupts_mask(void *arg)
 static void mvpp2_interrupts_unmask(void *arg)
 {
 	struct mvpp2_port *port = arg;
-	u32 val;
+	int cpu = smp_processor_id();
+	u32 val, thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
 	val = MVPP2_CAUSE_MISC_SUM_MASK |
 		MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
 	if (port->has_tx_irqs)
 		val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+			   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 }
 
 static void

@@ -1189,6 +1199,9 @@ static void mvpp2_interrupts_unmask(void *arg)
 
 		mvpp2_thread_write(port->priv, v->sw_thread_id,
 				   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+		mvpp2_thread_write(port->priv, v->sw_thread_id,
+				   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+				   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 	}
 }
 

@@ -2394,6 +2407,20 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
 	}
 }
 
+/* Set the number of non-occupied descriptors threshold */
+static void mvpp2_set_rxq_free_tresh(struct mvpp2_port *port,
+				     struct mvpp2_rx_queue *rxq)
+{
+	u32 val;
+
+	mvpp2_write(port->priv, MVPP2_RXQ_NUM_REG, rxq->id);
+
+	val = mvpp2_read(port->priv, MVPP2_RXQ_THRESH_REG);
+	val &= ~MVPP2_RXQ_NON_OCCUPIED_MASK;
+	val |= MSS_THRESHOLD_STOP << MVPP2_RXQ_NON_OCCUPIED_OFFSET;
+	mvpp2_write(port->priv, MVPP2_RXQ_THRESH_REG, val);
+}
+
 /* Set the number of packets that will be received before Rx interrupt
  * will be generated by HW.
  */

@@ -2649,6 +2676,9 @@ static int mvpp2_rxq_init(struct mvpp2_port *port,
 	mvpp2_rx_pkts_coal_set(port, rxq);
 	mvpp2_rx_time_coal_set(port, rxq);
 
+	/* Set the number of non occupied descriptors threshold */
+	mvpp2_set_rxq_free_tresh(port, rxq);
+
 	/* Add number of descriptors ready for receiving packets */
 	mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
 

@@ -766,9 +766,36 @@
 #define MSS_SRAM_SIZE			0x800
 #define MSS_FC_COM_REG			0
 #define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FLOW_CONTROL_UPDATE_COMMAND_BIT	BIT(31)
 #define FC_QUANTA			0xFFFF
 #define FC_CLK_DIVIDER			100
-#define MSS_THRESHOLD_STOP		768
+
+#define MSS_RXQ_TRESH_BASE		0x200
+#define MSS_RXQ_TRESH_OFFS		4
+#define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
+					* MSS_RXQ_TRESH_OFFS))
+
+#define MSS_RXQ_TRESH_START_MASK	0xFFFF
+#define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
+#define MSS_RXQ_TRESH_STOP_OFFS		16
+
+#define MSS_RXQ_ASS_BASE	0x80
+#define MSS_RXQ_ASS_OFFS	4
+#define MSS_RXQ_ASS_PER_REG	4
+#define MSS_RXQ_ASS_PER_OFFS	8
+#define MSS_RXQ_ASS_PORTID_OFFS	0
+#define MSS_RXQ_ASS_PORTID_MASK	0x3
+#define MSS_RXQ_ASS_HOSTID_OFFS	2
+#define MSS_RXQ_ASS_HOSTID_MASK	0x3F
+
+#define MSS_RXQ_ASS_Q_BASE(q, fq) ((((q) + (fq)) % MSS_RXQ_ASS_PER_REG)	 \
+				  * MSS_RXQ_ASS_PER_OFFS)
+#define MSS_RXQ_ASS_PQ_BASE(q, fq) ((((q) + (fq)) / MSS_RXQ_ASS_PER_REG) \
+				   * MSS_RXQ_ASS_OFFS)
+#define MSS_RXQ_ASS_REG(q, fq) (MSS_RXQ_ASS_BASE + MSS_RXQ_ASS_PQ_BASE(q, fq))
+
+#define MSS_THRESHOLD_STOP	768
+#define MSS_THRESHOLD_START	1024
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \

@@ -1026,6 +1053,9 @@ struct mvpp2 {
 
 	/* Global TX Flow Control config */
 	bool global_tx_fc;
+
+	/* Spinlocks for CM3 shared memory configuration */
+	spinlock_t mss_spinlock;
 };
 
 struct mvpp2_pcpu_stats {

@@ -1188,6 +1218,9 @@ struct mvpp2_port {
 	bool rx_hwtstamp;
 	enum hwtstamp_tx_types tx_hwtstamp_type;
 	struct mvpp2_hwtstamp_queue tx_hwtstamp_queue[2];
+
+	/* Firmware TX flow control */
+	bool tx_fc;
 };
 
 /* The mvpp2_tx_desc and mvpp2_rx_desc structures describe the

@@ -742,6 +742,110 @@ static void *mvpp2_buf_alloc(struct mvpp2_port *port,
 	return data;
 }
 
+/* Routine enable flow control for RXQs condition */
+static void mvpp2_rxq_enable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, host_id, q;
+	int fq = port->first_rxq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Set same Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set stop and start Flow control RXQ thresholds */
+		val = MSS_THRESHOLD_START;
+		val |= (MSS_THRESHOLD_STOP << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+		/* Set RXQ port ID */
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val |= (port->id << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		/* Calculate RXQ host ID:
+		 * In Single queue mode: Host ID equal to Host ID used for
+		 *			 shared RX interrupt
+		 * In Multi queue mode: Host ID equal to number of
+		 *			RXQ ID / number of CoS queues
+		 * In Single resource mode: Host ID always equal to 0
+		 */
+		if (queue_mode == MVPP2_QDIST_SINGLE_MODE)
+			host_id = port->nqvecs;
+		else if (queue_mode == MVPP2_QDIST_MULTI_MODE)
+			host_id = q;
+		else
+			host_id = 0;
+
+		/* Set RXQ host ID */
+		val |= (host_id << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
+/* Routine disable flow control for RXQs condition */
+static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, q;
+	unsigned long flags;
+	int fq = port->first_rxq;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Disable Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set threshold 0 to disable Flow control */
+		val = 0;
+		val |= (0 << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,

@@ -3006,6 +3110,9 @@ static void mvpp2_cleanup_rxqs(struct mvpp2_port *port)
 
 	for (queue = 0; queue < port->nrxqs; queue++)
 		mvpp2_rxq_deinit(port, port->rxqs[queue]);
+
+	if (port->tx_fc)
+		mvpp2_rxq_disable_fc(port);
 }
 
 /* Init all Rx queues for port */

@@ -3018,6 +3125,10 @@ static int mvpp2_setup_rxqs(struct mvpp2_port *port)
 		if (err)
 			goto err_cleanup;
 	}
+
+	if (port->tx_fc)
+		mvpp2_rxq_enable_fc(port);
+
 	return 0;
 
 err_cleanup:

@@ -4317,6 +4428,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
 
 	if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
 		new_rx_pending = MVPP2_MAX_RXD_MAX;
+	else if (ring->rx_pending < MSS_THRESHOLD_START)
+		new_rx_pending = MSS_THRESHOLD_START;
 	else if (!IS_ALIGNED(ring->rx_pending, 16))
 		new_rx_pending = ALIGN(ring->rx_pending, 16);
 

@@ -7170,6 +7283,9 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->hw_version = MVPP23;
 	}
 
+	/* Init mss lock */
+	spin_lock_init(&priv->mss_spinlock);
+
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
 	if (err < 0) {

@@ -324,6 +324,10 @@
 #define     MVPP2_BM_HIGH_THRESH_MASK		0x7f0000
 #define     MVPP2_BM_HIGH_THRESH_VALUE(val)	((val) << \
 						MVPP2_BM_HIGH_THRESH_OFFS)
+#define     MVPP2_BM_BPPI_HIGH_THRESH		0x1E
+#define     MVPP2_BM_BPPI_LOW_THRESH		0x1C
+#define     MVPP23_BM_BPPI_HIGH_THRESH		0x34
+#define     MVPP23_BM_BPPI_LOW_THRESH		0x28
 #define MVPP2_BM_INTR_CAUSE_REG(pool)		(0x6240 + ((pool) * 4))
 #define     MVPP2_BM_RELEASED_DELAY_MASK	BIT(0)
 #define     MVPP2_BM_ALLOC_FAILED_MASK		BIT(1)

@@ -352,6 +356,10 @@
 #define MVPP2_OVERRUN_ETH_DROP			0x7000
 #define MVPP2_CLS_ETH_DROP			0x7020
 
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG	0x6310
+#define     MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK	0xff
+#define     MVPP23_BM_8POOL_MODE		BIT(8)
+
 /* Hit counters registers */
 #define MVPP2_CTRS_IDX				0x7040
 #define     MVPP22_CTRS_TX_CTR(port, txq)	((txq) | ((port) << 3) | BIT(7))

@@ -70,6 +70,11 @@ enum mvpp2_bm_pool_log_num {
 module_param(queue_mode, int, 0444);
 MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
 
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
 /* Utility/helper methods */
 
 void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)

@@ -424,6 +429,21 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 
 	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
 	val |= MVPP2_BM_START_MASK;
+
+	val &= ~MVPP2_BM_LOW_THRESH_MASK;
+	val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+	/* Set 8 Pools BPPI threshold if BM underrun protection feature
+	 * were enabled
+	 */
+	if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+	} else {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+	}
+
 	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
 
 	bm_pool->size = size;

@@ -592,6 +612,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
 	return err;
 }
 
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+	val |= MVPP23_BM_8POOL_MODE;
+	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;

@@ -645,6 +675,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 	if (!priv->bm_pools)
 		return -ENOMEM;
 
+	if (priv->hw_version == MVPP23 && bm_underrun_protect)
+		mvpp23_bm_set_8pool_mode(priv);
+
 	err = mvpp2_bm_pools_init(dev, priv);
 	if (err < 0)
 		return err;

@@ -6491,7 +6524,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
-	if (port->priv->global_tx_fc) {
+	if (port->priv->global_tx_fc && bm_underrun_protect) {
 		port->tx_fc = tx_pause;
 		if (tx_pause)
 			mvpp2_rxq_enable_fc(port);

@@ -770,6 +770,18 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* RX FIFO threshold in 1KB granularity */
+#define MVPP23_PORT0_FIFO_TRSH	(9 * 1024)
+#define MVPP23_PORT1_FIFO_TRSH	(4 * 1024)
+#define MVPP23_PORT2_FIFO_TRSH	(2 * 1024)
+
+/* RX Flow Control Registers */
+#define MVPP2_RX_FC_REG(port)		(0x150 + 4 * (port))
+#define     MVPP2_RX_FC_EN		BIT(24)
+#define     MVPP2_RX_FC_TRSH_OFFS	16
+#define     MVPP2_RX_FC_TRSH_MASK	(0xFF << MVPP2_RX_FC_TRSH_OFFS)
+#define     MVPP2_RX_FC_TRSH_UNIT	256
+
 /* MSS Flow control */
 #define MSS_SRAM_SIZE			0x800
 #define MSS_FC_COM_REG			0

@@ -1502,6 +1514,8 @@ struct mvpp2_bm_pool {
 
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
 
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
+
 #ifdef CONFIG_MVPP2_PTP
 int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
 void mvpp22_tai_tstamp(struct mvpp2_tai *tai, u32 tstamp,

@@ -1534,4 +1548,5 @@ static inline bool mvpp22_rx_hwtstamping(struct mvpp2_port *port)
 {
 	return IS_ENABLED(CONFIG_MVPP2_PTP) && port->rx_hwtstamp;
 }
+
 #endif

@@ -6537,6 +6537,8 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
 			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
 		}
+		if (port->priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_en(port->priv, port->id, tx_pause);
 	}
 
 	mvpp2_port_enable(port);

@@ -7005,6 +7007,55 @@ static void mvpp22_rx_fifo_init(struct mvpp2 *priv)
 	mvpp2_write(priv, MVPP2_RX_FIFO_INIT_REG, 0x1);
 }
 
+/* Configure Rx FIFO Flow control thresholds */
+static void mvpp23_rx_fifo_fc_set_tresh(struct mvpp2 *priv)
+{
+	int port, val;
+
+	/* Port 0: maximum speed -10Gb/s port
+	 *	   required by spec RX FIFO threshold 9KB
+	 * Port 1: maximum speed -5Gb/s port
+	 *	   required by spec RX FIFO threshold 4KB
+	 * Port 2: maximum speed -1Gb/s port
+	 *	   required by spec RX FIFO threshold 2KB
+	 */
+
+	/* Without loopback port */
+	for (port = 0; port < (MVPP2_MAX_PORTS - 1); port++) {
+		if (port == 0) {
+			val = (MVPP23_PORT0_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else if (port == 1) {
+			val = (MVPP23_PORT1_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else {
+			val = (MVPP23_PORT2_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		}
+	}
+}
+
+/* Configure Rx FIFO Flow control thresholds */
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP2_RX_FC_REG(port));
+
+	if (en)
+		val |= MVPP2_RX_FC_EN;
+	else
+		val &= ~MVPP2_RX_FC_EN;
+
+	mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+}
+
 static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 {
 	int threshold = MVPP2_TX_FIFO_THRESHOLD(size);

@@ -7156,6 +7207,8 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	} else {
 		mvpp22_rx_fifo_init(priv);
 		mvpp22_tx_fifo_init(priv);
+		if (priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_set_tresh(priv);
 	}
 
 	if (priv->hw_version == MVPP21)

@@ -6284,7 +6284,7 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
-	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
+	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_FLOW_CTRL_MASK);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {

@@ -829,6 +829,7 @@
 
 #define MSS_THRESHOLD_STOP	768
 #define MSS_THRESHOLD_START	1024
+#define MSS_FC_MAX_TIMEOUT	5000
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \

@@ -932,6 +932,34 @@ static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+static int mvpp2_enable_global_fc(struct mvpp2 *priv)
+{
+	int val, timeout = 0;
+
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	/* Check if Firmware running and disable FC if not*/
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	while (timeout < MSS_FC_MAX_TIMEOUT) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+
+		if (!(val & FLOW_CONTROL_UPDATE_COMMAND_BIT))
+			return 0;
+		usleep_range(10, 20);
+		timeout++;
+	}
+
+	priv->global_tx_fc = false;
+	return -EOPNOTSUPP;
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,

@@ -7281,7 +7309,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err, val;
+	int err;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)

@@ -7509,13 +7537,13 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
-	/* Enable global flow control. In this stage global
-	 * flow control enabled, but still disabled per port.
-	 */
 	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
-		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
-		val |= FLOW_CONTROL_ENABLE_BIT;
-		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+		err = mvpp2_enable_global_fc(priv);
+		if (err) {
+			dev_warn(&pdev->dev, "CM3 firmware not running, version should be higher than 18.09 ");
+			dev_warn(&pdev->dev, "and chip revision B0\n");
+			dev_warn(&pdev->dev, "Flow control not supported\n");
+		}
 	}
 
 	mvpp2_dbgfs_init(priv, pdev->name);

@@ -775,6 +775,19 @@
 #define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
 					* MSS_RXQ_TRESH_OFFS))
 
+#define MSS_BUF_POOL_BASE		0x40
+#define MSS_BUF_POOL_OFFS		4
+#define MSS_BUF_POOL_REG(id)		(MSS_BUF_POOL_BASE		\
+					+ (id) * MSS_BUF_POOL_OFFS)
+
+#define MSS_BUF_POOL_STOP_MASK		0xFFF
+#define MSS_BUF_POOL_START_MASK		(0xFFF << MSS_BUF_POOL_START_OFFS)
+#define MSS_BUF_POOL_START_OFFS		12
+#define MSS_BUF_POOL_PORTS_MASK		(0xF << MSS_BUF_POOL_PORTS_OFFS)
+#define MSS_BUF_POOL_PORTS_OFFS		24
+#define MSS_BUF_POOL_PORT_OFFS(id)	(0x1 <<				\
+					((id) + MSS_BUF_POOL_PORTS_OFFS))
+
 #define MSS_RXQ_TRESH_START_MASK	0xFFFF
 #define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
 #define MSS_RXQ_TRESH_STOP_OFFS		16

@@ -846,6 +846,59 @@ static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+/* Routine disable/enable flow control for BM pool condition */
+static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
+				    struct mvpp2_bm_pool *pool,
+				    bool en)
+{
+	int val, cm3_state;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Check if BM pool should be enabled/disable */
+	if (en) {
+		/* Set BM pool start and stop thresholds per port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val |= MSS_BUF_POOL_PORT_OFFS(port->id);
+		val &= ~MSS_BUF_POOL_START_MASK;
+		val |= (MSS_THRESHOLD_START << MSS_BUF_POOL_START_OFFS);
+		val &= ~MSS_BUF_POOL_STOP_MASK;
+		val |= MSS_THRESHOLD_STOP;
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	} else {
+		/* Remove BM pool from the port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val &= ~MSS_BUF_POOL_PORT_OFFS(port->id);
+
+		/* Zero BM pool start and stop thresholds to disable pool
+		 * flow control if pool empty (not used by any port)
+		 */
+		if (!pool->buf_num) {
+			val &= ~MSS_BUF_POOL_START_MASK;
+			val &= ~MSS_BUF_POOL_STOP_MASK;
+		}
+
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,

@@ -1176,6 +1229,16 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		new_long_pool = MVPP2_BM_LONG;
 
 	if (new_long_pool != port->pool_long->id) {
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port,
+							port->pool_short,
+							false);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							false);
+		}
+
 		/* Remove port from old short & long pool */
 		port->pool_long = mvpp2_bm_pool_use(port, port->pool_long->id,
 						    port->pool_long->pkt_size);

@@ -1193,6 +1256,25 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		mvpp2_swf_bm_pool_init(port);
 
 		mvpp2_set_hw_csum(port, new_long_pool);
+
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							true);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_short,
+							true);
+		}
+
+		/* Update L4 checksum when jumbo enable/disable on port */
+		if (new_long_pool == MVPP2_BM_JUMBO && port->id != 0) {
+			dev->features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
+			dev->hw_features &= ~(NETIF_F_IP_CSUM |
+					      NETIF_F_IPV6_CSUM);
+		} else {
+			dev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+			dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+		}
 	}
 
 out_set:

@@ -6358,6 +6440,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 	u32 val;
+	int i;
 
 	if (mvpp2_is_xlg(interface)) {
 		if (!phylink_autoneg_inband(mode)) {

@@ -6408,6 +6491,21 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
+	if (port->priv->global_tx_fc) {
+		port->tx_fc = tx_pause;
+		if (tx_pause)
+			mvpp2_rxq_enable_fc(port);
+		else
+			mvpp2_rxq_disable_fc(port);
+		if (port->priv->percpu_pools) {
+			for (i = 0; i < port->nrxqs; i++)
+				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i], tx_pause);
+		} else {
+			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
+			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
+		}
+	}
+
 	mvpp2_port_enable(port);
 
 	mvpp2_egress_enable(port);

@@ -763,10 +763,12 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define MSS_SRAM_SIZE		0x800
-#define FC_QUANTA		0xFFFF
-#define FC_CLK_DIVIDER		100
-#define MSS_THRESHOLD_STOP	768
+#define MSS_SRAM_SIZE			0x800
+#define MSS_FC_COM_REG			0
+#define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FC_QUANTA			0xFFFF
+#define FC_CLK_DIVIDER			100
+#define MSS_THRESHOLD_STOP		768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \

@@ -1021,6 +1023,9 @@ struct mvpp2 {
 
 	/* CM3 SRAM pool */
 	struct gen_pool *sram_pool;
+
+	/* Global TX Flow Control config */
+	bool global_tx_fc;
 };
 
 struct mvpp2_pcpu_stats {

@@ -92,6 +92,16 @@ static inline u32 mvpp2_cpu_to_thread(struct mvpp2 *priv, int cpu)
 	return cpu % priv->nthreads;
 }
 
+static void mvpp2_cm3_write(struct mvpp2 *priv, u32 offset, u32 data)
+{
+	writel(data, priv->cm3_base + offset);
+}
+
+static u32 mvpp2_cm3_read(struct mvpp2 *priv, u32 offset)
+{
+	return readl(priv->cm3_base + offset);
+}
+
 static struct page_pool *
 mvpp2_create_page_pool(struct device *dev, int num, int len,
 		       enum dma_data_direction dma_dir)

@@ -5951,6 +5961,11 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 	phylink_set(mask, Autoneg);
 	phylink_set_port_modes(mask);
 
+	if (port->priv->global_tx_fc) {
+		phylink_set(mask, Pause);
+		phylink_set(mask, Asym_Pause);
+	}
+
 	switch (state->interface) {
 	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:

@@ -6969,7 +6984,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err;
+	int err, val;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)

@@ -7023,6 +7038,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 			return err;
 		else if (err)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
+
+		/* Enable global Flow Control only if handler to SRAM not NULL */
+		if (priv->cm3_base)
+			priv->global_tx_fc = true;
 	}
 
 	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {

@@ -7190,6 +7209,15 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+		val |= FLOW_CONTROL_ENABLE_BIT;
+		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+	}
+
 	mvpp2_dbgfs_init(priv, pdev->name);
 
 	platform_set_drvdata(pdev, priv);

@@ -596,6 +596,15 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
+/* FCA registers. PPv2.2 and PPv2.3 */
+#define MVPP22_FCA_BASE(port)			(0x7600 + (port) * 0x1000)
+#define MVPP22_FCA_REG_SIZE			16
+#define MVPP22_FCA_REG_MASK			0xFFFF
+#define MVPP22_FCA_CONTROL_REG			0x0
+#define MVPP22_FCA_ENABLE_PERIODIC		BIT(11)
+#define MVPP22_PERIODIC_COUNTER_LSB_REG		(0x110)
+#define MVPP22_PERIODIC_COUNTER_MSB_REG		(0x114)
+
 /* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0