Re: [PATCH RFC leds + net-next v3 2/2] net: phy: marvell: add support for PHY LEDs via LED class

On Sat, Jul 25, 2020 at 11:34:50AM +0200, Marek Behun wrote:

On Sat, 25 Jul 2020 11:23:39 +0200
Pavel Machek [off-list ref] wrote:

quoted

Hi!

quoted

+static const struct marvell_led_mode_info marvell_led_mode_info[] = {
+	{ "link",			{ 0x0,  -1, 0x0,  -1,  -1,  -1, }, 0 },
+	{ "link/act",			{ 0x1, 0x1, 0x1, 0x1, 0x1, 0x1, }, 0 },
+	{ "1Gbps/100Mbps/10Mbps",	{ 0x2,  -1,  -1,  -1,  -1,  -1, }, 0 },  

is this "1Gbps-10Mbps"?

Most of these modes mean "ON on event", eg
  "link" means ON when link up, else OFF. "
  "tx" means ON on when transmitting, else OFF
  "act" means ON when activity, else OFF
  "copper" means ON when copper link up, else OFF
but some are blinking modes
  "blink-act" means BLINK when activity, else OFF

Some modes can do ON and BLINK, these have one '/' in their name
  "link/act" means ON when link up, BLINK on activity, else OFF
  "link/rx" means ON when link up, BLINK on receive, else OFF

there is one mode, "1Gbps/100Mbps/10Mbps", which behaves differently:
  blinks 3 times when linked on 1Gbps
  blinks 2 times when linked on 100Mbps
  blinks 1 time when linked on 10Mbps
(and this blinking is repeating, ie blinks 3 times, pause, blinks 3 times,
pause)

Some modes are disjunctive:
  "100Mbps-fiber" means ON when linked on 100Mbps or via fiber, else OFF

Hi Marek

I would be good to added this to the sysfs documentation.

quoted

quoted

+	{ "act",			{ 0x3, 0x3, 0x3, 0x3, 0x3, 0x3, }, 0 },
+	{ "blink-act",			{ 0x4, 0x4, 0x4, 0x4, 0x4, 0x4, }, 0 },
+	{ "tx",				{ 0x5,  -1, 0x5,  -1, 0x5, 0x5, }, 0 },
+	{ "tx",				{  -1,  -1,  -1, 0x5,  -1,  -1, }, L3V5_TRANS },
+	{ "rx",				{  -1,  -1,  -1,  -1, 0x0, 0x0, }, 0 },
+	{ "rx",				{  -1, 0x0,  -1,  -1,  -1,  -1, }, L1V0_RECV },

To be consistent these four probably should have the blink- prefix. Or
it could be /tx, /rx ?

quoted

quoted

+	{ "copper",			{ 0x6,  -1,  -1,  -1,  -1,  -1, }, 0 },
+	{ "copper",			{  -1, 0x0,  -1,  -1,  -1,  -1, }, L1V0_COPPER },
+	{ "1Gbps",			{ 0x7,  -1,  -1,  -1,  -1,  -1, }, 0 },
+	{ "link/rx",			{  -1, 0x2,  -1, 0x2, 0x2, 0x2, }, 0 },
+	{ "100Mbps-fiber",		{  -1, 0x5,  -1,  -1,  -1,  -1, }, L1V5_100_FIBER },
+	{ "100Mbps-10Mbps",		{  -1, 0x5,  -1,  -1,  -1,  -1, }, L1V5_100_10 },
+	{ "1Gbps-100Mbps",		{  -1, 0x6,  -1,  -1,  -1,  -1, }, 0 },
+	{ "1Gbps-10Mbps",		{  -1,  -1, 0x6, 0x6,  -1,  -1, }, 0 },
+	{ "100Mbps",			{  -1, 0x7,  -1,  -1,  -1,  -1, }, 0 },
+	{ "10Mbps",			{  -1,  -1, 0x7,  -1,  -1,  -1, }, 0 },
+	{ "fiber",			{  -1,  -1,  -1, 0x0,  -1,  -1, }, L3V0_FIBER },
+	{ "fiber",			{  -1,  -1,  -1, 0x7,  -1,  -1, }, L3V7_FIBER },
+	{ "FullDuplex",			{  -1,  -1,  -1, 0x7,  -1,  -1, }, L3V7_DUPLEX },
+	{ "FullDuplex",			{  -1,  -1,  -1,  -1, 0x6, 0x6, }, 0 },
+	{ "FullDuplex/collision",	{  -1,  -1,  -1,  -1, 0x7, 0x7, }, 0 },
+	{ "FullDuplex/collision",	{  -1,  -1, 0x2,  -1,  -1,  -1, }, L2V2_DUPLEX },
+	{ "ptp",			{  -1,  -1, 0x2,  -1,  -1,  -1, }, L2V2_PTP },
+	{ "init",			{  -1,  -1, 0x2,  -1,  -1,  -1, }, L2V2_INIT },
+	{ "los",			{  -1,  -1,  -1, 0x0,  -1,  -1, }, L3V0_LOS },
+	{ "hi-z",			{ 0xa, 0xa, 0xa, 0xa, 0xa, 0xa, }, 0 },
+	{ "blink",			{ 0xb, 0xb, 0xb, 0xb, 0xb, 0xb, }, 0 },
+};  

Certainly more documentation will be required here, what "ptp" setting
does, for example, is not very obvious to me.

"ptp" means it will light up when the PTP functionality is enabled on
the PHY and a PTP packet is received.

Does hi-z mean off? In the implementation i did, i did not list off
and on as triggers. I instead used them for untriggered
brightness. That allowed the software triggers to work, so i had the
PHY blinking the heartbeat etc. But i had to make it optional, since a
quick survey of datasheets suggested not all PHYs support simple
on/off control.

Something beyond the scope of this patchset is implementing etHool -p

       -p --identify
              Initiates adapter-specific action intended to enable an operator to
	      easily identify the adapter by sight. Typically this involves  blink‐
              ing one or more LEDs on the specific network port.

If we have software controlled on/off, then a software trigger seems
like i good way to do this.

     Andrew