Re: [CFT 5/8] net: dpaa2-mac: use resolved link config in mac_link_up()

Convert the DPAA2 ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config(), which are
more suited to the needs of the DPAA2 MC firmware than those available
via mac_config().

Signed-off-by: Russell King <redacted>
---
 .../net/ethernet/freescale/dpaa2/dpaa2-mac.c  | 54 +++++++++++--------
 .../net/ethernet/freescale/dpaa2/dpaa2-mac.h  |  1 +
 2 files changed, 33 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
index 3a75c5b58f95..3ee236c5fc37 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c

@@ -123,35 +123,16 @@ static void dpaa2_mac_config(struct phylink_config *config, unsigned int mode,
 	struct dpmac_link_state *dpmac_state = &mac->state;
 	int err;
 
-	if (state->speed != SPEED_UNKNOWN)
-		dpmac_state->rate = state->speed;
-
-	if (state->duplex != DUPLEX_UNKNOWN) {
-		if (!state->duplex)
-			dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX;
-		else
-			dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX;
-	}
-
 	if (state->an_enabled)
 		dpmac_state->options |= DPMAC_LINK_OPT_AUTONEG;
 	else
 		dpmac_state->options &= ~DPMAC_LINK_OPT_AUTONEG;
 
-	if (state->pause & MLO_PAUSE_RX)
-		dpmac_state->options |= DPMAC_LINK_OPT_PAUSE;
-	else
-		dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE;
-
-	if (!!(state->pause & MLO_PAUSE_RX) ^ !!(state->pause & MLO_PAUSE_TX))
-		dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE;
-	else
-		dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE;
-
 	err = dpmac_set_link_state(mac->mc_io, 0,
 				   mac->mc_dev->mc_handle, dpmac_state);
 	if (err)
-		netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err);
+		netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n",
+			   __func__, err);
 }
 
 static void dpaa2_mac_link_up(struct phylink_config *config,

@@ -165,10 +146,37 @@ static void dpaa2_mac_link_up(struct phylink_config *config,
 	int err;
 
 	dpmac_state->up = 1;
+
+	if (mac->if_link_type == DPMAC_LINK_TYPE_PHY) {
+		/* If the DPMAC is configured for PHY mode, we need
+		 * to pass the link parameters to the MC firmware.
+		 */
+		dpmac_state->rate = speed;
+
+		if (duplex == DUPLEX_HALF)
+			dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX;
+		else if (duplex == DUPLEX_FULL)
+			dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX;
+
+		/* This is lossy; the firmware really should take the pause
+		 * enablement status rather than pause/asym pause status.
+		 */
+		if (rx_pause)
+			dpmac_state->options |= DPMAC_LINK_OPT_PAUSE;
+		else
+			dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE;
+
+		if (rx_pause ^ tx_pause)
+			dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE;
+		else
+			dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE;
+	}
+
 	err = dpmac_set_link_state(mac->mc_io, 0,
 				   mac->mc_dev->mc_handle, dpmac_state);
 	if (err)
-		netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err);
+		netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n",
+			   __func__, err);
 }
 
 static void dpaa2_mac_link_down(struct phylink_config *config,

@@ -241,6 +249,8 @@ int dpaa2_mac_connect(struct dpaa2_mac *mac)
 		goto err_close_dpmac;
 	}
 
+	mac->if_link_type = attr.link_type;
+
 	dpmac_node = dpaa2_mac_get_node(attr.id);
 	if (!dpmac_node) {
 		netdev_err(net_dev, "No dpmac@%d node found.\n", attr.id);

diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h
index 4da8079b9155..2130d9c7d40e 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h

@@ -20,6 +20,7 @@ struct dpaa2_mac {
 	struct phylink_config phylink_config;
 	struct phylink *phylink;
 	phy_interface_t if_mode;
+	enum dpmac_link_type if_link_type;
 };
 
 bool dpaa2_mac_is_type_fixed(struct fsl_mc_device *dpmac_dev,

-- 
2.20.1