On Wed, Dec 18, 2019 at 03:00:41PM +0000, Alexandru Marginean wrote:

On 12/18/2019 2:29 PM, Russell King - ARM Linux admin wrote:

quoted

On Wed, Dec 18, 2019 at 03:21:02PM +0200, Vladimir Oltean wrote:

quoted

- The at803x.c driver explicitly checks for the ACK from the MAC PCS,
and prints "SGMII link is not ok" otherwise, and refuses to bring the
link up. This hurts us in 4.19 because I think the check is a bit
misplaced in the .aneg_done callback. To be precise, what we observe
is that this function is not called by the state machine a second,
third time etc to recheck if the AN has completed in the meantime. In
current net-next, as far as I could figure out, at803x_aneg_done is
dead code. What is ironic about the commit f62265b53ef3 ("at803x:
double check SGMII side autoneg") that introduced this function is
that it's for the gianfar driver (Freescale eTSEC), a MAC that has
never supported reprogramming itself based on the in-band config word.
In fact, if you look at gfar_configure_serdes, it even configures its
register 0x4 with an advertisement for 1000Base-X, not SGMII (0x4001).
So I really wonder if there is any real purpose to this check in
at803x_aneg_done, and if not, I would respectfully remove it.

Please check whether at803x will pass data if the SGMII config exchange
has not completed - I'm aware of some PHYs that, although link comes up
on the copper side, if AN does not complete on the SGMII side, they
will not pass data, even if the MAC side is forced up.

I don't see any configuration bits in the 8031 that suggest the SGMII
config exchange can be bypassed.

quoted

- The vsc8514 PHY driver configures SerDes AN in U-Boot, but not in
Linux. So we observe that if we disable PHY configuration in U-Boot,
in-band AN breaks in Linux. We are actually wondering how we should
fix this: from what you wrote above, it seems ok to hardcode SGMII AN
in the PHY driver, and just ignore it in the PCS if managed =
"in-band-status" is not set with PHYLINK. But as you said, in the
general case maybe not all PHYs work until they haven't received the
ACK from the MAC PCS, which makes this insufficient as a general
solution.

But the 2 cases above illustrate the lack of consistency among PHY
drivers w.r.t. in-band aneg.

Indeed - it's something of a mine field at the moment, because we aren't
quite sure whether "SGMII" means that the PHY requires in-band AN or
doesn't provide it. For the Broadcom case I mentioned, when it's used on
a SFP, I've had to add a quirk to phylink to work around it.

The problem is, it's not a case that the MAC can demand that the PHY
provides in-band config - some PHYs are incapable of doing so. Whatever
solution we come up with needs to be a "negotiation" between the PHY
driver and the MAC driver for it to work well in the known scenarios -
like the case with the Broadcom PHY on a SFP that can be plugged into
any SFP supporting network interface...

Some sort of capability negotiation does seem to be the proper solution.
We can have a new capabilities field in phydev for system interface 
capabilities and match that with MAC capabilities, configuration, factor 
in the quirks.  The result would tell if a solution is possible, 
especially with quirky PHYs, and if PHY drivers need to enable AN.

Until we have that in place, any recommended approach for PHY drivers, 
is it acceptable to hardcode system side AN on as a short term fix?
I've just tested VSC8514 and it doesn't allow traffic through if SI AN 
is enabled but does not complete.  We do use it with AN on on NXP 
systems, and it only works because U-Boot sets things up that way, but 
relying on U-Boot isn't great.
Aquantia PHYs we use also require AN to complete if enabled.  For them 
Linux depends on U-Boot or on PHY firmware to enable AN.  I don't know 
if anyone out there uses these PHYs with AN off.  Would a patch that 
hardcodes AN on for any of these PHYs be acceptable?

I'm not sure why you're talking about hard-coding anything. As I've
already mentioned, phylink allows you to specify today whether you
want to use in-band AN or not, provided the MAC implements it as is
done with mvneta and mvpp2.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up