Re: [PATCH RFC] Update documentation for KSZ DSA drivers so that new drivers can be added

On 09/08/2017 12:48 PM, Tristram.Ha@microchip.com wrote:

quoted

-----Original Message-----
From: Maxim Uvarov [mailto:muvarov@gmail.com]
Sent: Friday, September 08, 2017 12:00 PM
To: Florian Fainelli
Cc: Tristram Ha - C24268; Andrew Lunn; Pavel Machek; Nathan Conrad; Vivien
Didelot; netdev; linux-kernel@vger.kernel.org; Woojung Huh - C21699
Subject: Re: [PATCH RFC] Update documentation for KSZ DSA drivers so that new
drivers can be added

2017-09-08 21:48 GMT+03:00 Florian Fainelli [off-list ref]:

quoted

On 09/07/2017 02:11 PM, Tristram.Ha@microchip.com wrote:

quoted

From: Tristram Ha <redacted>

Add other KSZ switches support so that patch check does not complain.

Signed-off-by: Tristram Ha <redacted>
---
 Documentation/devicetree/bindings/net/dsa/ksz.txt | 117
++++++++++++----------
 1 file changed, 62 insertions(+), 55 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt

b/Documentation/devicetree/bindings/net/dsa/ksz.txt
index 0ab8b39..34af0e0 100644

--- a/Documentation/devicetree/bindings/net/dsa/ksz.txt
+++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt

@@ -3,8 +3,15 @@ Microchip KSZ Series Ethernet switches

 Required properties:

-- compatible: For external switch chips, compatible string must be

exactly one
-  of: "microchip,ksz9477"
+- compatible: Should be "microchip,ksz9477" for KSZ9477 chip,
+           "microchip,ksz8795" for KSZ8795 chip,
+           "microchip,ksz8794" for KSZ8794 chip,
+           "microchip,ksz8765" for KSZ8765 chip,
+           "microchip,ksz8895" for KSZ8895 chip,
+           "microchip,ksz8864" for KSZ8864 chip,
+           "microchip,ksz8873" for KSZ8873 chip,
+           "microchip,ksz8863" for KSZ8863 chip,
+           "microchip,ksz8463" for KSZ8463 chip

Tristram, does any of this devices support chaining?

Maxim.

They do not if you mean daisy-chaining the switches together.

Marvell tags allow you to specify both a port and switch index
destination after setting up an appropriate routing table, I am assuming
this is not supported.

What happens though if I connect two KSZ switches ones to another say:

eth0
	-> KSZ8463
		-> KSZ8463

Will the first switch terminates KSZ tag if it sees two tags
encapsulated in another, something like this:

| MAC DA | MAC SA | .... payload | Inner KSZ tag | Inner KSZ tag | FCS |

There is always a problem that once tail tagging mode is enabled
sending a frame through the MAC without going through the DSA
layer will cause the frame to be dropped.

Yes, once the master network device is used for DSA, it is still usable
directly by e.g: applications, but it won't do anything if the switch is
configured such that it drops ingressing frames not having the proper
tag. We documented that here:

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/networking/dsa/dsa.txt#n275
-- 
Florian