Re: [PATCHv3 (net.git) 2/2] stmmac: fix MDIO settings

Hi Peppe,

Am 11.03.2016 um 14:33 schrieb Giuseppe Cavallaro:

Initially the phy_bus_name was added to manipulate the
driver name but It was recently just used to manage the

"it"

fixed-link and then to take some decision at run-time
inside the main (for example to skip EEE).

Word missing after "main"? ("function"?)

So the patch uses the is_pseudo_fixed_link and removes
removes the phy_bus_name variable not necessary anymore.

Duplicate "removes".

The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).

Signed-off-by: Giuseppe Cavallaro <redacted>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <redacted>
Cc: Gabriel Fernandez <redacted>
Cc: Dinh Nguyen <redacted>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <redacted>
---

V2: use is_pseudo_fixed_link
V3: parse device-tree driver parameters to allocate PHY resources considering
    DSA case (+ fixed-link).

For next-20160314 I needed "i2c: immediately mark ourselves as
registered" plus this build fix:

--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -866,9 +866,8 @@ static int stmmac_init_phy(struct net_device *dev)
        }

        /* If attached to a switch, there is no reason to poll phy

handler */
-       if (priv->plat->phy_bus_name)
-               if (!strcmp(priv->plat->phy_bus_name, "fixed"))
-                       phydev->irq = PHY_IGNORE_INTERRUPT;
+       if (phydev->is_pseudo_fixed_link)
+               phydev->irq = PHY_IGNORE_INTERRUPT;

        pr_debug("stmmac_init_phy:  %s: attached to PHY (UID 0x%x)"
                 " Link = %d\n", dev->name, phydev->phy_id, phydev->link);

It then fixes the PHY error on GeekBox, so for this mini-series:

Tested-by: Andreas Färber <afaerber@suse.de>


The connectivity issue still remains. Kernel log snippet:

[  +0.001117] rk_gmac-dwmac ff290000.ethernet: Looking up phy-supply
from device tree
[  +0.000028] rk808 0-001b: Looking up vcc12-supply from device tree
[  +0.000014] vcc_lan: supplied by vcc_io
[  +0.000101] rk_gmac-dwmac ff290000.ethernet: clock input or output?
(input).
[  +0.000009] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30).
[  +0.000008] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10).
[  +0.000014] rk_gmac-dwmac ff290000.ethernet: init for RGMII
[  +0.000104] rk_gmac-dwmac ff290000.ethernet: clock input from PHY
[  +0.005063] rk_gmac-dwmac ff290000.ethernet: no reset control found
[  +0.000007] stmmac - user ID: 0x10, Synopsys ID: 0x35
[  +0.000002]  Ring mode enabled
[  +0.000006]  DMA HW capability register supported
[  +0.000000]  Normal descriptors
[  +0.000003]  RX Checksum Offload Engine supported (type 2)
[  +0.000002]  TX Checksum insertion supported
[  +0.000002]  Wake-Up On Lan supported
[  +0.000053]  Enable RX Mitigation via HW Watchdog Timer
[  +0.000771] of_get_named_gpiod_flags: can't parse 'snps,reset-gpio'
property of node '/ethernet@ff290000[0]'
[  +0.004250] libphy: stmmac: probed
[  +0.000009] eth0: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[  +0.000005] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)

As before, reverting "stmmac: first frame prep at the end of xmit
routine" fixes it. My test cases are `ping 192.168.1.1` and `zypper up`.

Regards,
Andreas

-- 
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton; HRB 21284 (AG Nürnberg)