[net-next 04/15] ixgbe: add new media type

@@ -527,6 +527,66 @@ static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
 }
 
 /**
+ *  ixgbe_set_fiber_fixed_speed - Set module link speed for fixed fiber
+ *  @hw: pointer to hardware structure
+ *  @speed: link speed to set
+ *
+ *  We set the module speed differently for fixed fiber.  For other
+ *  multi-speed devices we don't have an error value so here if we
+ *  detect an error we just log it and exit.
+ */
+static void ixgbe_set_fiber_fixed_speed(struct ixgbe_hw *hw,
+					ixgbe_link_speed speed)
+{
+	s32 status;
+	u8 rs, eeprom_data;
+
+	switch (speed) {
+	case IXGBE_LINK_SPEED_10GB_FULL:
+		/* one bit mask same as setting on */
+		rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
+		break;
+	case IXGBE_LINK_SPEED_1GB_FULL:
+		rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
+		break;
+	default:
+		hw_dbg(hw, "Invalid fixed module speed\n");
+		return;
+	}
+
+	/* Set RS0 */
+	status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+					   IXGBE_I2C_EEPROM_DEV_ADDR2,
+					   &eeprom_data);
+	if (status) {
+		hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
+		goto out;
+	}
+
+	eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs;
+
+	status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+					    IXGBE_I2C_EEPROM_DEV_ADDR2,
+					    eeprom_data);
+	if (status) {
+		hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
+		goto out;
+	}
+
+	eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs;
+
+	status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
+					    IXGBE_I2C_EEPROM_DEV_ADDR2,
+					    eeprom_data);
+	if (status) {
+		hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
+		goto out;
+	}
+out:
+	return;
+}
+
+/**
  *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
  *  @hw: pointer to hardware structure
  *  @speed: new link speed

@@ -573,9 +633,14 @@ static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 			goto out;
 
 		/* Set the module link speed */
-		esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
-		IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
-		IXGBE_WRITE_FLUSH(hw);
+		if (hw->phy.media_type == ixgbe_media_type_fiber_fixed) {
+			ixgbe_set_fiber_fixed_speed(hw,
+					IXGBE_LINK_SPEED_10GB_FULL);
+		} else {
+			esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
+			IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+			IXGBE_WRITE_FLUSH(hw);
+		}
 
 		/* Allow module to change analog characteristics (1G->10G) */
 		msleep(40);

@@ -625,10 +690,15 @@ static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 			goto out;
 
 		/* Set the module link speed */
-		esdp_reg &= ~IXGBE_ESDP_SDP5;
-		esdp_reg |= IXGBE_ESDP_SDP5_DIR;
-		IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
-		IXGBE_WRITE_FLUSH(hw);
+		if (hw->phy.media_type == ixgbe_media_type_fiber_fixed) {
+			ixgbe_set_fiber_fixed_speed(hw,
+						IXGBE_LINK_SPEED_1GB_FULL);
+		} else {
+			esdp_reg &= ~IXGBE_ESDP_SDP5;
+			esdp_reg |= IXGBE_ESDP_SDP5_DIR;
+			IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+			IXGBE_WRITE_FLUSH(hw);
+		}
 
 		/* Allow module to change analog characteristics (10G->1G) */
 		msleep(40);

@@ -72,6 +72,7 @@ s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
 	bool link_up;
 
 	switch (hw->phy.media_type) {
+	case ixgbe_media_type_fiber_fixed:
 	case ixgbe_media_type_fiber:
 		hw->mac.ops.check_link(hw, &speed, &link_up, false);
 		/* if link is down, assume supported */

@@ -138,6 +139,7 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw)
 	 * we link at 10G, the 1G advertisement is harmless and vice versa.
 	 */
 	switch (hw->phy.media_type) {
+	case ixgbe_media_type_fiber_fixed:
 	case ixgbe_media_type_fiber:
 	case ixgbe_media_type_backplane:
 		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);

@@ -2404,6 +2406,7 @@ void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 
 	switch (hw->phy.media_type) {
 	/* Autoneg flow control on fiber adapters */
+	case ixgbe_media_type_fiber_fixed:
 	case ixgbe_media_type_fiber:
 		if (speed == IXGBE_LINK_SPEED_1GB_FULL)
 			ret_val = ixgbe_fc_autoneg_fiber(hw);

@@ -44,6 +44,8 @@
 #define IXGBE_SFF_CABLE_SPEC_COMP    0x3C
 #define IXGBE_SFF_SFF_8472_SWAP      0x5C
 #define IXGBE_SFF_SFF_8472_COMP      0x5E
+#define IXGBE_SFF_SFF_8472_OSCB         0x6E
+#define IXGBE_SFF_SFF_8472_ESCB         0x76
 
 /* Bitmasks */
 #define IXGBE_SFF_DA_PASSIVE_CABLE           0x4

@@ -54,6 +56,9 @@
 #define IXGBE_SFF_1GBASET_CAPABLE            0x8
 #define IXGBE_SFF_10GBASESR_CAPABLE          0x10
 #define IXGBE_SFF_10GBASELR_CAPABLE          0x20
+#define IXGBE_SFF_SOFT_RS_SELECT_MASK   0x8
+#define IXGBE_SFF_SOFT_RS_SELECT_10G    0x8
+#define IXGBE_SFF_SOFT_RS_SELECT_1G     0x0
 #define IXGBE_SFF_ADDRESSING_MODE	     0x4
 #define IXGBE_I2C_EEPROM_READ_MASK           0x100
 #define IXGBE_I2C_EEPROM_STATUS_MASK         0x3

@@ -2622,6 +2622,7 @@ enum ixgbe_sfp_type {
 enum ixgbe_media_type {
 	ixgbe_media_type_unknown = 0,
 	ixgbe_media_type_fiber,
+	ixgbe_media_type_fiber_fixed,
 	ixgbe_media_type_fiber_lco,
 	ixgbe_media_type_copper,
 	ixgbe_media_type_backplane,