Re: BUG - 2.4.37 fealnx.c NETDEV WATCHDOG: eth0: transmit timed out

Hello,

On Fri, Jan 02, 2009 at 08:10:50PM +0530, Jaswinder Singh Rajput wrote:

Hello all,

Now I tested fealnx driver from 2.4.37 (2.4 git). I am still getting
"NETDEV WATCHDOG: eth0: transmit timed out". Please let me know how
can I fix this problem.

Well, I don't have such an adapter, but most of the times I encountered
a similar message with older 10/100 adapters, it was caused by a link
status issue or duplex mismatch.

Could you check with ethtool or mii-diag that the link status is correct
and 100 Mbps/Full duplex (assuming you're connected to a switch) ?

fealnx.c:v2.51 Nov-17-2001
eth0: 100/10M Ethernet PCI Adapter at 0x6200, 00:40:95:78:05:73, IRQ 11.

NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
  Rx ring c11bf000:  80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
  Tx ring c11be000:  80000000 80000000 80000000 80000000 0000 80000000
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
  Rx ring c11bf000:  80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
  Tx ring c11be000:  80000000 0000 80000000 80000000 80000000 80000000
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
  Rx ring c11bf000:  80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
  Tx ring c11be000:  80000000 80000000 80000000 80000000 80000000 0000


00:0a.0 Ethernet controller: MYSON Technology Inc: Unknown device 0803
	Subsystem: MYSON Technology Inc: Unknown device 0803
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 6200 [size=256]
	Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=1K]
	Expansion ROM at <unassigned> [disabled] [size=64K]
	Capabilities: [88] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0-,D1+,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Thank you,
JSR

Regards,
Willy