Hello,
On Fri, Jan 02, 2009 at 08:10:50PM +0530, Jaswinder Singh Rajput wrote:
Hello all,
Now I tested fealnx driver from 2.4.37 (2.4 git). I am still getting
"NETDEV WATCHDOG: eth0: transmit timed out". Please let me know how
can I fix this problem.
Well, I don't have such an adapter, but most of the times I encountered
a similar message with older 10/100 adapters, it was caused by a link
status issue or duplex mismatch.
Could you check with ethtool or mii-diag that the link status is correct
and 100 Mbps/Full duplex (assuming you're connected to a switch) ?
fealnx.c:v2.51 Nov-17-2001
eth0: 100/10M Ethernet PCI Adapter at 0x6200, 00:40:95:78:05:73, IRQ 11.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
Tx ring c11be000: 80000000 80000000 80000000 80000000 0000 80000000
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
Tx ring c11be000: 80000000 0000 80000000 80000000 80000000 80000000
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 00000000, resetting...
Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000
80000000 80000000 80000000 80000000 80000000 80000000 80000000
Tx ring c11be000: 80000000 80000000 80000000 80000000 80000000 0000
00:0a.0 Ethernet controller: MYSON Technology Inc: Unknown device 0803
Subsystem: MYSON Technology Inc: Unknown device 0803
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 6200 [size=256]
Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [88] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0-,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Thank you,
JSR
Hello Willy,
On 1/2/09, Willy Tarreau [off-list ref] wrote:
On Fri, Jan 02, 2009 at 08:10:50PM +0530, Jaswinder Singh Rajput wrote:
quoted
Now I tested fealnx driver from 2.4.37 (2.4 git). I am still getting
"NETDEV WATCHDOG: eth0: transmit timed out". Please let me know how
can I fix this problem.
Well, I don't have such an adapter, but most of the times I encountered
a similar message with older 10/100 adapters, it was caused by a link
status issue or duplex mismatch.
I think I am also getting same problem, what is the solution.
Could you check with ethtool or mii-diag that the link status is correct
and 100 Mbps/Full duplex (assuming you're connected to a switch) ?
Output of mii-diag -v :
eth0: 10 Mbit, half duplex, no link
product info: vendor 00:00:00, model 0 rev 0
basic mode: 10 Mbit, half duplex
basic status: no link
capabilities:
advertising:
This is the output from very old machine Pentium MMX with Redhat 7.1
I also tested different RTL8139 adapters on different machines with
different kernels and different kind of switches and Hubs but I get
same error on all the machines. But my other Network devices are
working perfectly.
Thank you,
JSR
Output of mii-diag -v :
eth0: 10 Mbit, half duplex, no link
product info: vendor 00:00:00, model 0 rev 0
basic mode: 10 Mbit, half duplex
basic status: no link
capabilities:
advertising:
This is the output from very old machine Pentium MMX with Redhat 7.1
Can you check with 'mii-tool -vv eth0' that the mii registers are not
all zeroes ?
--
Ueimor
On Sat, Jan 3, 2009 at 12:27 AM, Francois Romieu [off-list ref] wrote:
Jaswinder Singh Rajput [off-list ref] :
[..]
quoted
Output of mii-diag -v :
eth0: 10 Mbit, half duplex, no link
product info: vendor 00:00:00, model 0 rev 0
basic mode: 10 Mbit, half duplex
basic status: no link
capabilities:
advertising:
This is the output from very old machine Pentium MMX with Redhat 7.1
Can you check with 'mii-tool -vv eth0' that the mii registers are not
all zeroes ?
Yes all are zeros :-)
eth0: 10 Mbit, half duplex, no link
registers for MII PHY 32:
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
product info: vendor 00:00:00, model 0 rev 0
basic mode: 10 Mbit, half duplex
basic status: no link
capabilities:
advertising:
Now what is next step.
Thank you,
JSR