This series modernizes the QUICC Engine Port Interrupt Controller (QE
PIC) driver and adds the ability for QE GPIO pins to generate interrupts
through the QE PIC, completing Christophe Leroy's prior work [1].

Christophe's series was partially merged; patches 4, 6 and 7 did not
make it to mainline.

The series is organized in three parts:

1) Add missing chained_irq_{enter,exit}() calls

   - In a chained handler, the parent controller need to mask and ack
     the interrupt source.

2) DT binding updates

   - Update #interrupt-cells from 1 to 2 in the QE PIC binding so
     consumers can encode the interrupt type (falling-edge or
     both-edges).

   - Convert the QE GPIO binding from freeform text to DT schema.

   - Extend the QE GPIO binding with an interrupt-map (nexus node) that
     maps GPIO lines to parent QE PIC interrupts.  This approach was
     suggested by Rob Herring [2] as an alternative to using compatible
     strings and driver data to specify which pins support interrupts in
     a given bank.

3) QE PIC driver refactoring

   - The QE PIC is a perfect fit to use the generic irq framework
     instead. Perform the necessary changes to the driver to convert it.

   - Minor cleanups.

4) QE GPIO interrupt support

   - Add a to_irq() method to the QE GPIO driver that perform the
     mapping of the GPIO pin to the parent interrupt domain, allowing
     GPIO pins to be used as interrupt sources through the QE PIC via
     gpio_to_irq().

[1] https://lore.kernel.org/all/cover.1758212309.git.christophe.leroy@csgroup.eu/ (local)
[2] https://lore.kernel.org/all/20250919152414.GB852815-robh@kernel.org/ (local)

Signed-off-by: Paul Louvel <redacted>

---
Christophe Leroy (1):
      dt-bindings: soc: fsl: qe: Convert QE GPIO to DT schema

Paul Louvel (11):
      soc: fsl: qe: Add chained_irq_{enter,exit}() calls in cascade handler
      dt-bindings: soc: fsl: qe: Set #interrupt-cells to 2 to support interrupt type encoding
      dt-bindings: soc: fsl: qe: Add support of IRQ in QE GPIO
      soc: fsl: qe: Use generic_handle_domain_irq()
      soc: fsl: qe: Iterate over all pending interrupts in cascade handler
      soc: fsl: qe: Handle spurious interrupts
      soc: fsl: qe: Convert to generic IRQ chip
      soc: fsl: qe: Rename irq variable to parent_irq
      soc: fsl: qe: Rename host member to domain in struct qepic_data
      soc: fsl: qe: Remove useless struct member
      soc: fsl: qe: Add support of IRQs in QE GPIO

 .../bindings/gpio/fsl,mpc8323-qe-pario-bank.yaml   | 108 ++++++++++++++++
 .../interrupt-controller/fsl,qe-ports-ic.yaml      |   4 +-
 .../bindings/soc/fsl/cpm_qe/qe/par_io.txt          |  26 +---
 arch/powerpc/platforms/Kconfig                     |   1 +
 drivers/soc/fsl/qe/gpio.c                          |  28 +++-
 drivers/soc/fsl/qe/qe_ports_ic.c                   | 144 +++++++++++++--------
 6 files changed, 232 insertions(+), 79 deletions(-)
---
base-commit: f1b7f9c6e1a7fc549f37cafb48d233c9f7c26adc
change-id: 20260513-qe-pic-gpios-073e284615a3

Best regards,
--  
Paul Louvel, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com