Re: onboard pci ethernet controller(i82551)without eprom(linuxppc2.2.4 MPC5200)

=E6=82=A8=E5=A5=BD,

I am using the same chip connected through PCI to a Virtex-II Pro (PPC=20
405).  I do not have an EEPROM connected to the chip.  However, I am=20
having problem with the code because it seems to be built specifically=20
for processors that have coherent cache.  So each time the code tries to =

execute I get a kernel panic. (kernel 2.4.26, with RTAI patch)

This occurs because in many places it executes a bottom-half spin lock=20
before calling pci_free_consistent.  This increments the bottom-half=20
counter and so when pci_free_consistent is called it calls BUG(); and=20
the whole thing goes Tango Uniform.  I'm about to go through and try to=20
fix this, but it seems like an extremely dangerous thing for me to play=20
with.

I seem to be able to get the eepro100.c code to work, but I was hoping=20
to use the e100 driver to program an EEPROM on the board.

=E8=B0=A2=E8=B0=A2

Joshua

=C3=8F=C3=84=C3=93=C3=AA wrote:

After i modified e100_init() in e100_main.c , the pci ethernet card coul=

d been found :

bash-2.05b# ifconfig -a
eth0      Link encap:Ethernet  HWaddr FF:FF:FF:FF:FF:FF
         BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
         Memory:40000000-40000038

eth1      Link encap:Ethernet  HWaddr 00:04:9F:00:15:2B
         inet addr:198.87.102.215  Bcast:198.87.102.255  Mask:255.255.2=

55.0

         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:12606 errors:42 dropped:0 overruns:0 frame:0
         TX packets:7668 errors:3 dropped:0 overruns:3 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:10596597 (10.1 Mb)  TX bytes:1218624 (1.1 Mb)
         Interrupt:43

lo        Link encap:Local Loopback
         inet addr:127.0.0.1  Mask:255.0.0.0
         UP LOOPBACK RUNNING  MTU:16436  Metric:1
         RX packets:4 errors:0 dropped:0 overruns:0 frame:0
         TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0

But i still could not config eth0:

bash-2.05b# ifconfig eth0 198.87.102.140
SIOCSIFFLAGS: Resource temporarily unavailable

I noticed that there was message as blow during kernel bootup:

POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 00:1a.0
Linux NET4.0 for Linux 2.4

Intel(R) PRO/100 Network Driver - version 2.3.38-k1
Copyright (c) 2004 Intel Corporation

PCI: Enabling device 00:18.0 (0006 -> 0007)
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled

IP-Config: Failed to open eth0

what is wrong?

Best regards

Xiayu







_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

=20

--=20

Xiphos Technologies
(514) 848-9640 x227
(514) 848-9644 fax

www.xiplink.com
_______________________________________________
The information transmitted is intended only for the
person or entity to which it is addressed and may contain
confidential and/or privileged material.  If you have
received this in error, please contact the sender and delete
this communication and any copy immediately. Thank you.