After i modified e100_init() in e100_main.c , the pci ethernet card could been found :
bash-2.05b# ifconfig -a
eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:40000000-40000038
eth1 Link encap:Ethernet HWaddr 00:04:9F:00:15:2B
inet addr:198.87.102.215 Bcast:198.87.102.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12606 errors:42 dropped:0 overruns:0 frame:0
TX packets:7668 errors:3 dropped:0 overruns:3 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10596597 (10.1 Mb) TX bytes:1218624 (1.1 Mb)
Interrupt:43
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
But i still could not config eth0:
bash-2.05b# ifconfig eth0 198.87.102.140
SIOCSIFFLAGS: Resource temporarily unavailable
I noticed that there was message as blow during kernel bootup:
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 00:1a.0
Linux NET4.0 for Linux 2.4
Intel(R) PRO/100 Network Driver - version 2.3.38-k1
Copyright (c) 2004 Intel Corporation
PCI: Enabling device 00:18.0 (0006 -> 0007)
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
IP-Config: Failed to open eth0
what is wrong?
Best regards
Xiayu
--- ÏÄÓêÏÄÓêiayxiayinariays.com> wrote:
After i modified e100_initinitn e100_main.c , the pci
pcieethernetcard could been found :
bash-2.05b# ifcoifconfig
eth0eth Link encaencapernet HWadHWaddrFF:FF:FF:FF:FF
BROADCAST MULTMULTICASTU:MTU0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqutxqueuelen0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:40000000-40000038
eth1eth Link encaencapernet HWadHWaddr04:9F:00:15:2B
inetinetraddr.87.102.215 BcasBcast.87.102.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTMULTICASTU:MTU0 Metric:1
RX packets:12606 errors:42 dropped:0 overruns:0
frame:0
TX packets:7668 errors:3 dropped:0 overruns:3
carrier:0
collisions:0 txqutxqueuelen0
RX bytes:10596597 (10.1 Mb) TX bytes:1218624 (1.1
Mb)
Interrupt:43
lo Link encaencapal LoopLoopback
inetinetraddr.0.0.1 Mask:255.0.0.0
UP LOOPLOOPBACKNING MTU:MTU36 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqutxqueuelen>
But i still could not confconfig0eth>
bash-2.05b# ifcoifconfig0eth8.87.102.140
SIOCSIOCSIFFLAGSsource temporarily unavailable
I noticed that there was message as blow during kernel
bootbootup
POSIPOSIXformance testing by UNIFUNIFIXPCI:PCIobing PCI
PCIdware
PCI:PCInnot allocate resource region 0 of device 00:1a.0
Linux NET4.0 for Linux 2.4
Intel(R) PRO/100 Network Driver - version 2.3.38-k1
Copyright (c) 2004 Intel Corporation
PCI:PCIabling device 00:18.0 (0006 -> 0007)
e100: eth0ethntel(R) PRO/100 Network Connection
Hardware receive checchecksumsbled
IP-CIPfConfigiled to open eth0eth
what is wrong?
Best regards
XiayXiayuu don't have a valid mac address. Try
temptemporarilydhard codingand see what happens...
_______________________________________________
LinuLinuxppcedded mailing list
LinuLinuxppcedded@ozlaozlabs
httphttpszlaozlabs/mailman/listlistinfoulinuxppcedded
__________________________________
Yahoo! Mail - PC Magazine Editors' Choice 2005
http://mail.yahoo.com
=E6=82=A8=E5=A5=BD,
I am using the same chip connected through PCI to a Virtex-II Pro (PPC=20
405). I do not have an EEPROM connected to the chip. However, I am=20
having problem with the code because it seems to be built specifically=20
for processors that have coherent cache. So each time the code tries to =
execute I get a kernel panic. (kernel 2.4.26, with RTAI patch)
This occurs because in many places it executes a bottom-half spin lock=20
before calling pci_free_consistent. This increments the bottom-half=20
counter and so when pci_free_consistent is called it calls BUG(); and=20
the whole thing goes Tango Uniform. I'm about to go through and try to=20
fix this, but it seems like an extremely dangerous thing for me to play=20
with.
I seem to be able to get the eepro100.c code to work, but I was hoping=20
to use the e100 driver to program an EEPROM on the board.
=E8=B0=A2=E8=B0=A2
Joshua
=C3=8F=C3=84=C3=93=C3=AA wrote:
After i modified e100_init() in e100_main.c , the pci ethernet card coul=
d been found :
bash-2.05b# ifconfig -a
eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:40000000-40000038
eth1 Link encap:Ethernet HWaddr 00:04:9F:00:15:2B
inet addr:198.87.102.215 Bcast:198.87.102.255 Mask:255.255.2=
55.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12606 errors:42 dropped:0 overruns:0 frame:0
TX packets:7668 errors:3 dropped:0 overruns:3 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10596597 (10.1 Mb) TX bytes:1218624 (1.1 Mb)
Interrupt:43
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
But i still could not config eth0:
bash-2.05b# ifconfig eth0 198.87.102.140
SIOCSIFFLAGS: Resource temporarily unavailable
I noticed that there was message as blow during kernel bootup:
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 00:1a.0
Linux NET4.0 for Linux 2.4
Intel(R) PRO/100 Network Driver - version 2.3.38-k1
Copyright (c) 2004 Intel Corporation
PCI: Enabling device 00:18.0 (0006 -> 0007)
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
IP-Config: Failed to open eth0
what is wrong?
Best regards
Xiayu
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
=20
--=20
Xiphos Technologies
(514) 848-9640 x227
(514) 848-9644 fax
www.xiplink.com
_______________________________________________
The information transmitted is intended only for the
person or entity to which it is addressed and may contain
confidential and/or privileged material. If you have
received this in error, please contact the sender and delete
this communication and any copy immediately. Thank you.