[PATCH v3 17/20] scsi: ufs: ufs-qcom: Factor out the logic finding the HS Gear
From: Manivannan Sadhasivam <hidden>
Date: 2022-11-23 07:52:13
Also in:
linux-arm-msm, linux-scsi, lkml
Subsystem:
arm/qualcomm mailing list, scsi subsystem, the rest, universal flash storage host controller driver qualcomm hooks · Maintainers:
"James E.J. Bottomley", "Martin K. Petersen", Linus Torvalds, Manivannan Sadhasivam
In the preparation of adding support for new gears, let's move the logic that finds the gear for each platform to a new function. This helps with code readability and also allows the logic to be used in other places of the driver in future. While at it, let's make it clear that this driver only supports symmetric gear setting (hs_tx_gear == hs_rx_gear). Reviewed-by: Andrew Halaney <redacted> Signed-off-by: Manivannan Sadhasivam <redacted> --- drivers/ufs/host/ufs-qcom.c | 34 +++++++++++++++++++++------------- 1 file changed, 21 insertions(+), 13 deletions(-)
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 38e2ed749d75..919b6eae439d 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c@@ -278,6 +278,25 @@ static int ufs_qcom_host_reset(struct ufs_hba *hba) return 0; } +static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = ufshcd_get_variant(hba); + + if (host->hw_ver.major == 0x1) { + /* + * HS-G3 operations may not reliably work on legacy QCOM + * UFS host controller hardware even though capability + * exchange during link startup phase may end up + * negotiating maximum supported gear as G3. + * Hence downgrade the maximum supported gear to HS-G2. + */ + return UFS_HS_G2; + } + + /* Default is HS-G3 */ + return UFS_HS_G3; +} + static int ufs_qcom_power_up_sequence(struct ufs_hba *hba) { struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -692,19 +711,8 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba, ufshcd_init_pwr_dev_param(&ufs_qcom_cap); ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE; - if (host->hw_ver.major == 0x1) { - /* - * HS-G3 operations may not reliably work on legacy QCOM - * UFS host controller hardware even though capability - * exchange during link startup phase may end up - * negotiating maximum supported gear as G3. - * Hence downgrade the maximum supported gear to HS-G2. - */ - if (ufs_qcom_cap.hs_tx_gear > UFS_HS_G2) - ufs_qcom_cap.hs_tx_gear = UFS_HS_G2; - if (ufs_qcom_cap.hs_rx_gear > UFS_HS_G2) - ufs_qcom_cap.hs_rx_gear = UFS_HS_G2; - } + /* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */ + ufs_qcom_cap.hs_tx_gear = ufs_qcom_cap.hs_rx_gear = ufs_qcom_get_hs_gear(hba); ret = ufshcd_get_pwr_dev_param(&ufs_qcom_cap, dev_max_params,
--
2.25.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy