Hi Paul,

于 Fri, 25 Jun 2021 16:47:30 +0100
Paul Cercueil [off-list ref] 写道:

Hi Zhou,

Le ven., juin 25 2021 at 23:19:42 +0800, 周琰杰 
[off-list ref] a écrit :

quoted

Hi Paul,

于 Fri, 25 Jun 2021 12:31:17 +0100
Paul Cercueil [off-list ref] 写道:
  

quoted

 Hi Zhou,

 Le jeu., juin 24 2021 at 23:06:29 +0800, 周琰杰 (Zhou Yanjie)
 [off-list ref] a écrit :  
 > 1.Add a new TCU channel as the percpu timer of core1, this is to
 >   prepare for the subsequent SMP support. The newly added
 > channel will not adversely affect the current single-core state.
 > 2.Adjust the position of TCU node to make it consistent with the
 >   order in jz4780.dtsi file.  

 That's a bit superfluous, the order matters when adding new nodes,
 but once they are added, moving them around only cause annoyance.
  
 >
 > Signed-off-by: 周琰杰 (Zhou Yanjie) [off-list ref]
 > ---
 >
 > Notes:
 >     v2:
 >     New patch.
 >
 >     v2->v3:
 >     No change.
 >
 >  arch/mips/boot/dts/ingenic/ci20.dts | 21 +++++++++++----------
 >  1 file changed, 11 insertions(+), 10 deletions(-)
 >
 > diff --git a/arch/mips/boot/dts/ingenic/ci20.dts
 > b/arch/mips/boot/dts/ingenic/ci20.dts
 > index 8877c62..70005cc 100644
 > --- a/arch/mips/boot/dts/ingenic/ci20.dts
 > +++ b/arch/mips/boot/dts/ingenic/ci20.dts
 > @@ -118,6 +118,17 @@
 >  	assigned-clock-rates = <48000000>;
 >  };
 >
 > +&tcu {
 > +	/*
 > +	 * 750 kHz for the system timers and 3 MHz for the
 > clocksources,
 > +	 * use channel #0 and #1 for the per cpu system timers,
 > and use
 > +	 * channel #2 for the clocksource.
 > +	 */
 > +	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu  
 > TCU_CLK_TIMER1>,  
 > +					  <&tcu
 > TCU_CLK_TIMER2>, <&tcu TCU_CLK_OST>;
 > +	assigned-clock-rates = <750000>, <750000>, <3000000>,
 > <3000000>;  

 Ideally you'd set TIMER1 to 3 MHz and TIMER2 to 750 kHz,
otherwise it
 kind of breaks support for older kernels (they would still boot,
but with a very slow clocksource). So in the new DTS you could use
the timer0 clock for CPU #0, timer1 for the clocksource, and
timer2+ for cpus > 0.  

I checked the ingenic-timer driver, and it seems that the last TCU
channel is always used as the clocksource in the driver, so it seems
that we can only use timer2 as the clocksource in smp mode. Maybe we
should add a note for smp is closed in the comment. And I found
that I missed a problem, Nikolaus Schaller once reported that
because the frequency of the tcu timer (only 16bit) used to provide
the clocksource
is too high, there will be a chance that the system will get stuck
before the clocksource is switched to ost. And reducing the 
clocksource
to 750kz can prevent it from happening. I will add this part to v4.
When this part is added, both clockevent and clocksource will be
750kHz, but the 750kHz clocksource is only temporary, because it
will then switch to the clocksource provided by ost, and ost works
at 3MHz.  

Ok, then first change the clocksource to 750 kHz, then update it with 
timer2.

Sure, I will do it in v4.

Thanks and best regards!

Cheers,
-Paul

quoted

Thanks and best regards!
  

quoted

 Cheers,
 -Paul
  
 > +};
 > +
 >  &mmc0 {
 >  	status = "okay";
 >
 > @@ -522,13 +533,3 @@
 >  		bias-disable;
 >  	};
 >  };
 > -
 > -&tcu {
 > -	/*
 > -	 * 750 kHz for the system timer and 3 MHz for the
 > clocksource,
 > -	 * use channel #0 for the system timer, #1 for the
 > clocksource.
 > -	 */
 > -	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu  
 > TCU_CLK_TIMER1>,  
 > -					  <&tcu TCU_CLK_OST>;
 > -	assigned-clock-rates = <750000>, <3000000>, <3000000>;
 > -};
 > --
 > 2.7.4
 >