[PATCH 1/5] serial: 8250: Document SMSC Super I/O UART peculiarities
From: "Maciej W. Rozycki" <macro@orcam.me.uk>
Date: 2021-06-10 18:38:34
Also in:
linux-serial, lkml
Contrary to what SMSC documentation says and unlike NS16C550A UARTs the
SMSC Super I/O IC claims compatibility with the SMSC UART implementation
does not support dividing the internal PLL clock by any divisor from 1
to 65535[1], with the exception of two magic divisors of 32769 and 32770
used respectively to select the high-speed data rates of 460800bps and
230400bps[2] if enabled on a port-by-port basis in with the Serial Port
Mode Register in the Device Configuration Space[3][4].
Instead empirical evidence indicates that the divisor, as stored in the
DLL and DLM register pair, has the range of 1 to 32767 only, and bit 7
of the DLM register (bit 15 of the divisor) effectively serves as a
selection bit for the prescaler from the base frequency of 7.3728MHz,
either 4 if the bit is 0, or 1 if the bit is 1 and high-speed operation
has been enabled with the Serial Port Mode Register.
So if high-speed operation has not been enabled, then say the values of
1 and 32769 (0x8001) written into the combined DLL and DLM register pair
both select the divisor of 1 and the baud rate of 115200bps.
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Section "Programmable Baud Rate Generator (and Divisor
Latches DLH, DLL)", p. 75
[2] same, Table 31 - "Baud Rates", p. 77
[3] same, Table 60 - "Serial Port 1, Logical Device 4 [Logical Device
Number = 0x04]", p. 153
[4] same, Table 61 - "Serial Port 2, Logical Device 5 [Logical Device
Number = 0x05]", p. 153
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
---
drivers/tty/serial/8250/8250_port.c | 31 +++++++++++++++++++++++++++++--
1 file changed, 29 insertions(+), 2 deletions(-)
linux-serial-8250-magic-multiplier-doc.diff
Index: linux-malta-cbus-uart/drivers/tty/serial/8250/8250_port.c
===================================================================--- linux-malta-cbus-uart.orig/drivers/tty/serial/8250/8250_port.c
+++ linux-malta-cbus-uart/drivers/tty/serial/8250/8250_port.c@@ -2519,9 +2519,36 @@ static unsigned int serial8250_do_get_di unsigned int quot; /* - * Handle magic divisors for baud rates above baud_base on - * SMSC SuperIO chips. + * Handle magic divisors for baud rates above baud_base on SMSC + * Super I/O chips. We clamp custom rates from clk/6 and clk/12 + * up to clk/4 (0x8001) and clk/8 (0x8002) respectively. These + * magic divisors actually reprogram the baud rate generator's + * reference clock derived from chips's 14.318MHz clock input. + * + * Documentation claims that with these magic divisors the base + * frequencies of 7.3728MHz and 3.6864MHz are used respectively + * for the extra baud rates of 460800bps and 230400bps rather + * than the usual base frequency of 1.8462MHz. However empirical + * evidence contradicts that. * + * Instead bit 7 of the DLM register (bit 15 of the divisor) is + * effectively used as a clock prescaler selection bit for the + * base frequency of 7.3728MHz, always used. If set to 0, then + * the base frequency is divided by 4 for use by the Baud Rate + * Generator, for the usual arrangement where the value of 1 of + * the divisor produces the baud rate of 115200bps. Conversely, + * if set to 1 and high-speed operation has been enabled with the + * Serial Port Mode Register in the Device Configuration Space, + * then the base frequency is supplied directly to the Baud Rate + * Generator, so for the divisor values of 0x8001, 0x8002, 0x8003, + * 0x8004, etc. the respective baud rates produced are 460800bps, + * 230400bps, 153600bps, 115200bps, etc. + * + * In all cases only low 15 bits of the divisor are used to divide + * the baud base and therefore 32767 is the maximum divisor value + * possible, even though documentation says that the programmable + * Baud Rate Generator is capable of dividing the internal PLL + * clock by any divisor from 1 to 65535. */ if ((port->flags & UPF_MAGIC_MULTIPLIER) && baud == (port->uartclk/4))