Thread (19 messages) 19 messages, 2 authors, 2020-02-14
STALE2296d
Revisions (7)
  1. v1 [diff vs current]
  2. v2 current
  3. v3 [diff vs current]
  4. v4 [diff vs current]
  5. v5 [diff vs current]
  6. v6 [diff vs current]
  7. v7 [diff vs current]

[PATCH v2 00/12] MIPS: Fixes and improvements for CI20 board (JZ4780)

From: H. Nikolaus Schaller <hidden>
Date: 2020-02-14 16:11:46
Also in: dri-devel, linux-devicetree, lkml

V2:
* dropped "net: davicom: dm9000: allow to pass MAC address through mac_addr module parameter"
  from this series because it goes through the netdev tree
  (suggested by Andrew Lunn [off-list ref])
* added a "fixes:" for "MIPS: DTS: CI20: fix PMU definitions for ACT8600"
  and "MIPS: DTS: CI20: fix interrupt for pcf8563 RTC"
  (suggested by Andreas Kemnade [off-list ref])
* "i2c: jz4780: silence log flood on txabrt" dropped because it is
  replaced by a new version in v5.6 by Wolfram Sang [off-list ref]

PATCH V1 2020-02-11 22:41:43:
This patch set provides several improvements for the CI20 board:

* suppress warnings from i2c if device is not responding
* make ingenic-drm found through DT
* allow davicom dm9000 ethernet controller to use MAC address provided by U-Boot
* fix #include in jz4780.dtsi
* configure for loadable kernel modules
* add DTS for IR sensor and SW1 button
* configure so that LEDs, IR sensor, SW1 button have drivers
* fix DTS for ACT8600 PMU and configure driver
* fix interrupt of nxp,pcf8563

There is another patch set in our queue to add HDMI support on top of this work.

Signed-off-by: Paul Boddie <redacted>
Signed-off-by: H. Nikolaus Schaller <redacted>


Alex Smith (1):
  MIPS: DTS: CI20: add DT node for IR sensor

H. Nikolaus Schaller (11):
  drm: ingenic-drm: add MODULE_DEVICE_TABLE
  MIPS: DTS: jz4780: add #includes for irq.h and gpio.h
  MIPS: CI20: defconfig: configure for supporting modules
  MIPS: CI20: defconfig: compile leds-gpio driver into the kernel and
    configure for LED triggers
  MIPS: DTS: CI20: fix PMU definitions for ACT8600
  MIPS: CI20: defconfig: configure CONFIG_REGULATOR_ACT8865 for PMU
  MIPS: DTS: CI20: give eth0_power a defined voltage.
  MIPS: CI20: defconfig: compile gpio-ir driver
  MIPS: DTS: CI20: add DT node for SW1 as Enter button
  MIPS: CI20: defconfig: configure for CONFIG_KEYBOARD_GPIO=m
  MIPS: DTS: CI20: fix interrupt for pcf8563 RTC

 arch/mips/boot/dts/ingenic/ci20.dts    | 71 ++++++++++++++++++++------
 arch/mips/boot/dts/ingenic/jz4780.dtsi |  2 +
 arch/mips/configs/ci20_defconfig       | 21 ++++++++
 drivers/gpu/drm/ingenic/ingenic-drm.c  |  2 +
 4 files changed, 80 insertions(+), 16 deletions(-)

-- 
2.23.0
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help