[RFC PATCH v3 2/5] Documentation: synopsys-dw-mshc: add bindings for idmac and edmac
From: Shawn Lin <shawn.lin@rock-chips.com>
Date: 2015-08-05 08:17:52
Also in:
linux-devicetree, linux-mmc, linux-rockchip, linux-samsung-soc
Subsystem:
multimedia card (mmc), secure digital (sd) and sdio subsystem, open firmware and flattened device tree bindings, the rest · Maintainers:
Ulf Hansson, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
synopsys-dw-mshc supports three types of transfer mode. We add bindings and description for how to use them at runtime. Without idmac and edmac property, pio is the default transfer mode. Make sure that Idmac and emdac should not be used simultaneously. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> --- Changes in v3: None Changes in v2: None .../devicetree/bindings/mmc/synopsys-dw-mshc.txt | 41 ++++++++++++++++++++++ 1 file changed, 41 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 346c609..30369cb 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt@@ -75,6 +75,25 @@ Optional properties: * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. +* supports-idmac: Enables support for internal DMAC block within the Synopsys + Designware Mobile Storage IP block. If supports-idmac property is present, then + we MUST NOT add supports-edmac property since we'd assume that dw-mshc IP is + integrated with only one type of dma master. + +* supports-edmac: Enables support for external DMAC block outside the Synopsys + Designware Mobile Storage IP block. If supports-edmac property is present, then + we MUST NOT add supports-idmac property since we'd assume that dw-mshc IP is + integrated with only one type of dma master. + + (Without "supports-idmac" and "supports-edmac", use PIO as default transfer mode) + +* dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. This property should be combined with + supports-edmac. Refer to dma.txt for details. + +* dma-names: DMA request names. Must be "rx-tx". And This property should be + combined with supports-edmac. Refer to dma.txt for details. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using
@@ -95,6 +114,8 @@ board specific portions as listed below. #size-cells = <0>; }; +[board specific internal DMA resources] + dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>;
@@ -106,4 +127,24 @@ board specific portions as listed below. bus-width = <8>; cap-mmc-highspeed; cap-sd-highspeed; + supports-idmac; }; + +[board specific generic DMA request binding] + + dwmmc0@12200000 { + clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; + num-slots = <1>; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + vmmc-supply = <&buck8>; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + supports-edmac; + dmas = <&pdma 12>; + dma-names = "rx-tx"; + }; +
--
2.3.7