[PATCH v2 13/15] HID: ft260: i2c: reject an I2C clock outside the supported range

From
Michael Zaidman <michael.zaidman@gmail.com>
Date
2026-10-30 22:37:26
Also in
linux-gpio, linux-i2c, linux-serial, lkml
Reply to
Michael Zaidman, 2026-10-30
The clock sysfs attribute passes any 16-bit value to the chip. The chip
accepts it, reports it back in the I2C status report that clock_show
reads, and runs the bus at the 100 kHz default. A read of 2048 bytes
takes the same 0.298 s after writing 50, 3500 or 65535 as it does after
writing 100, while 60 and 3400 give 0.387 s and 0.058 s. Userspace has
no way to see that the value was not applied.

Refuse a value outside the 60-3400 kHz range named in the datasheet
section 4.4.16. ft260_uart_change_speed() checks the baud rate against
FT260_UART_CFG_BAUD_MIN and FT260_UART_CFG_BAUD_MAX, but termios has no
error return, so it falls back to 9600. A sysfs store can return an
error, so the clock store refuses the value.

FT260_WORD_ATTR_STORE() takes the parse function as a parameter now, so
a word attribute with no range of its own keeps passing kstrtou16.

Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
---
 drivers/hid/hid-ft260.c | 31 ++++++++++++++++++++++++++++---
 1 file changed, 28 insertions(+), 3 deletions(-)
diff --git a/drivers/hid/hid-ft260.c b/drivers/hid/hid-ft260.c
index 50f68790c04d..f7d01d9e07f7 100644
--- a/drivers/hid/hid-ft260.c
+++ b/drivers/hid/hid-ft260.c
@@ -68,6 +68,11 @@ MODULE_PARM_DESC(debug, "Toggle FT260 debugging messages");
 
 #define FT260_WR_I2C_DATA_MAX 60
 #define FT260_WR_UART_DATA_MAX 62
+
+/* I2C bus clock range in kHz, see the FT260 datasheet section 4.4.16 */
+#define FT260_I2C_CLOCK_MIN 60
+#define FT260_I2C_CLOCK_MAX 3400
+
 #define FT260_GPIOCHIP "ft260_gpio"
 #define FT260_GPIO_0_5_COUNT 6
 #define FT260_GPIO_A_H_COUNT 8
@@ -1529,6 +1534,25 @@ static void ft260_attr_dummy_func(struct hid_device *hdev, u8 req, u16 value)
 {
 }
 
+/*
+ * The chip takes any 16-bit value and reports it back in the I2C status
+ * report, but runs the bus at the 100 kHz default when the value is
+ * outside the documented range. The report gives no way to tell the two
+ * cases apart, so refuse the value here.
+ */
+static int ft260_i2c_clock_parse(const char *buf, unsigned int base, u16 *clock)
+{
+	int ret = kstrtou16(buf, base, clock);
+
+	if (ret)
+		return ret;
+
+	if (*clock < FT260_I2C_CLOCK_MIN || *clock > FT260_I2C_CLOCK_MAX)
+		return -EINVAL;
+
+	return 0;
+}
+
 #define FT260_ATTR_SHOW(name, reptype, id, type, func)			       \
 	static ssize_t name##_show(struct device *kdev,			       \
 				   struct device_attribute *attr, char *buf)   \
@@ -1586,9 +1610,9 @@ static void ft260_attr_dummy_func(struct hid_device *hdev, u8 req, u16 value)
 		FT260_ATTR_STORE(name, reptype, FT260_SYSTEM_SETTINGS, req,    \
 				 u8, kstrtou8, func, FT260_STORE_NATIVE)
 
-#define FT260_WORD_ATTR_STORE(name, reptype, req, func)			       \
+#define FT260_WORD_ATTR_STORE(name, reptype, req, strtou, func)		       \
 		FT260_ATTR_STORE(name, reptype, FT260_SYSTEM_SETTINGS, req,    \
-				 u16, kstrtou16, func, cpu_to_le16)
+				 u16, strtou, func, cpu_to_le16)
 
 FT260_SSTAT_ATTR_SHOW(chip_mode);
 static DEVICE_ATTR_RO(chip_mode);
@@ -1641,7 +1665,8 @@ static DEVICE_ATTR_RW(clock_ctl);
 
 FT260_I2CST_ATTR_SHOW(clock);
 FT260_WORD_ATTR_STORE(clock, ft260_set_i2c_speed_report,
-		      FT260_SET_I2C_CLOCK_SPEED, ft260_attr_dummy_func);
+		      FT260_SET_I2C_CLOCK_SPEED, ft260_i2c_clock_parse,
+		      ft260_attr_dummy_func);
 static DEVICE_ATTR_RW(clock);
 
 static ssize_t i2c_reset_store(struct device *kdev,
-- 
2.43.0
Thread (27 messages) 27 messages, 3 authors, last reply 10d ago
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help