Re: [PATCH v3 5/6] dt-bindings: mfd: Add Delta TN48M CPLD drivers bindings

On Wed, Jun 2, 2021 at 12:47 PM Lee Jones [off-list ref] wrote:

On Mon, 31 May 2021, Robert Marko wrote:

quoted

Add binding documents for the Delta TN48M CPLD drivers.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v3:
* Include bindings for reset driver

Changes in v2:
* Implement MFD as a simple I2C MFD
* Add GPIO bindings as separate

 .../bindings/gpio/delta,tn48m-gpio.yaml       | 42 +++++++++
 .../bindings/mfd/delta,tn48m-cpld.yaml        | 90 +++++++++++++++++++
 .../bindings/reset/delta,tn48m-reset.yaml     | 35 ++++++++
 3 files changed, 167 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/delta,tn48m-gpio.yaml
 create mode 100644 Documentation/devicetree/bindings/mfd/delta,tn48m-cpld.yaml
 create mode 100644 Documentation/devicetree/bindings/reset/delta,tn48m-reset.yaml

quoted

+++ b/Documentation/devicetree/bindings/mfd/delta,tn48m-cpld.yaml

@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/delta,tn48m-cpld.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Delta Networks TN48M CPLD controller
+
+maintainers:
+  - Robert Marko <robert.marko@sartura.hr>
+
+description: |
+  Lattice CPLD onboard the TN48M switches is used for system
+  management.
+
+  It provides information about the hardware model, revision,
+  PSU status etc.
+
+  It is also being used as a GPIO expander for the SFP slots and
+  reset controller for the switch MAC-s and other peripherals.
+
+properties:
+  compatible:
+    const: delta,tn48m-cpld
+
+  reg:
+    description:
+      I2C device address.
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+patternProperties:
+  "^gpio(@[0-9a-f]+)?$":
+    $ref: ../gpio/delta,tn48m-gpio.yaml
+
+  "^reset-controller?$":
+    $ref: ../reset/delta,tn48m-reset.yaml
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        cpld@41 {
+            compatible = "delta,tn48m-cpld";
+            reg = <0x41>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            gpio@31 {
+                compatible = "delta,tn48m-gpio-sfp-tx-disable";
+                reg = <0x31>;
+                gpio-controller;
+                #gpio-cells = <2>;
+            };
+
+            gpio@3a {
+                compatible = "delta,tn48m-gpio-sfp-present";
+                reg = <0x3a>;
+                gpio-controller;
+                #gpio-cells = <2>;
+            };
+
+            gpio@40 {
+                compatible = "delta,tn48m-gpio-sfp-los";
+                reg = <0x40>;
+                gpio-controller;
+                #gpio-cells = <2>;
+            };
+
+            reset-controller {
+              compatible = "delta,tn48m-reset";
+              #reset-cells = <1>;
+            };

How is the Reset component addressed?

It has a defined register in the driver.
Now that I think of it, it would make sense to use reg for it like for the GPIO
and not hardcode it.

Regards,
Robert

quoted

+        };
+    };

--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

-- 
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr