Re: [PATCH 1/2] dt-bindings: backlight: rt4831: Add the new property for ocp level selection

Krzysztof Kozlowski [off-list ref] 於 2022年6月2日 週四 下午9:58寫道：

On 02/06/2022 15:56, Rob Herring wrote:

quoted

On Thu, May 26, 2022 at 12:32:12PM +0200, Krzysztof Kozlowski wrote:

quoted

On 26/05/2022 10:13, ChiYuan Huang wrote:

quoted

Krzysztof Kozlowski [off-list ref] 於 2022年5月26日 週四 下午4:06寫道：

quoted

On 26/05/2022 05:16, cy_huang wrote:

quoted

From: ChiYuan Huang <redacted>

Add the new property for ocp level selection.

Signed-off-by: ChiYuan Huang <redacted>
---
 .../bindings/leds/backlight/richtek,rt4831-backlight.yaml         | 8 ++++++++
 include/dt-bindings/leds/rt4831-backlight.h                       | 5 +++++
 2 files changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/leds/backlight/richtek,rt4831-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/richtek,rt4831-backlight.yaml
index e0ac686..c1c59de 100644
--- a/Documentation/devicetree/bindings/leds/backlight/richtek,rt4831-backlight.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/richtek,rt4831-backlight.yaml

@@ -47,6 +47,14 @@ properties:
     minimum: 0
     maximum: 3

+  richtek,bled-ocp-sel:

Skip "sel" as it is a shortcut of selection. Name instead:
"richtek,backlight-ocp"

OK, if so, do I need to rename all properties from 'bled' to 'backlight' ?
If  only this property is naming as 'backlight'. it may conflict with
the others like as "richtek,bled-ovp-sel".

Ah, no, no need.

quoted

quoted

quoted

+    description: |
+      Backlight OCP level selection, currently support 0.9A/1.2A/1.5A/1.8A

Could you explain here what is OCP (unfold the acronym)?

Yes. And the full name is 'over current protection'.

Thanks and this leads to second thing - you encode register value
instead of logical value. This must be a logical value in mA, so
"richtek,bled-ocp-microamp".

We already have common properties for setting current of LEDs. We should
use that here I think.

It might not be exactly the same. We have "led-max-microamp" which is
the maximum allowed current. I guess over-current protection level  is
slightly higher (e.g. led-max-microamp + 1). IOW, led-max-microamp is
something which still can be set and used by system/hardware. OCP should
not.

Yap, you're right.
From the modern backlight IC design, it uses the boost converter architecture.
This OCP level is to limit the inductor current when the internal MOS
switch turn on.
Details can refer to the below wiki link
https://en.wikipedia.org/wiki/Boost_converter

And based on it, OVP is used to limit the inductor output voltage.
Each channel maximum current is based on the IC affordable limit.
It is more like as what you said 'led-max-microamp'.

So boost voltage level may depend on the LED VF.
The different series of LED may cause different boost voltage.

RT4831's OVP/OCP is not just the protection, more like as the limit.

Best regards,
Krzysztof