On Mon, Feb 13, 2023 at 08:24:32PM +0530, Neeraj Sanjay Kale wrote:
quoted hunk ↗ jump to hunk
This adds a driver based on serdev driver for the NXP BT serial
protocol based on running H:4, which can enable the built-in
Bluetooth device inside a generic NXP BT chip.
This driver has Power Save feature that will put the chip into
sleep state whenever there is no activity for 2000ms, and will
be woken up when any activity is to be initiated over UART.
This driver enables the power save feature by default by sending
the vendor specific commands to the chip during setup.
During setup, the driver checks if a FW is already running on the
chip based on the CTS line, and downloads device specific FW file
into the chip over UART.
The driver contains certain device specific default parameters
related to FW filename, baudrate and timeouts which can be
overwritten by an optional user space config file. These parameters
may vary from one module vendor to another.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
---
v2: Removed conf file support and added static data for each chip
based on compatibility devices mentioned in DT bindings. Handled
potential memory leaks and null pointer dereference issues,
simplified FW download feature, handled byte-order and few cosmetic
changes. (Ilpo Järvinen, Alok Tiwari, Hillf Danton)
v3: Added conf file support necessary to support different vendor
modules, moved .h file contents to .c, cosmetic changes. (Luiz
Augusto von Dentz, Rob Herring, Leon Romanovsky)
---
drivers/bluetooth/Kconfig | 11 +
drivers/bluetooth/Makefile | 1 +
drivers/bluetooth/btnxpuart.c | 1370 +++++++++++++++++++++++++++++++++
3 files changed, 1382 insertions(+)
create mode 100644 drivers/bluetooth/btnxpuart.c
diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index 5a1a7bec3c42..773b40d34b7b 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -465,4 +465,15 @@ config BT_VIRTIO
Say Y here to compile support for HCI over Virtio into the
kernel or say M to compile as a module.
+config BT_NXPUART
+ tristate "NXP protocol support"
+ depends on SERIAL_DEV_BUS
+ help
+ NXP is serial driver required for NXP Bluetooth
+ devices with UART interface.
+
+ Say Y here to compile support for NXP Bluetooth UART device into
+ the kernel, or say M here to compile as a module.
What is the module name?
+#define MAX_TAG_STR_LEN 20
+#define BT_FW_CONF_FILE "nxp/bt_mod_para.conf"
You can not load "configuration files" as firmware, as that is not what
firmware is for.
Firmware is to be sent straight to the device, the kernel is not
supposed to do any parsing like you are doing:
quoted hunk ↗ jump to hunk
+#define USER_CONFIG_TAG "user_config"
+#define FW_NAME_TAG "fw_name"
+#define OPER_SPEED_TAG "oper_speed"
+#define FW_DL_PRI_BAUDRATE_TAG "fw_dl_pri_speed"
+#define FW_DL_SEC_BAUDRATE_TAG "fw_dl_sec_speed"
+#define FW_INIT_BAUDRATE "fw_init_speed"
+#define PS_INTERVAL_MS "ps_interval_ms"
With these values.
Please use the normal kernel interfaces for configuring your device.
that is NOT the firmware interface, sorry.
thanks,
greg k-h