On 20/05/2021 18:06, Ryan Chen wrote:

quoted

-----Original Message-----
From: openbmc
[off-list ref] On Behalf
Of Quan Nguyen
Sent: Wednesday, May 19, 2021 3:50 PM
To: Corey Minyard <redacted>; Rob Herring <robh+dt@kernel.org>;
Joel Stanley [off-list ref]; Andrew Jeffery [off-list ref]; Brendan
Higgins [off-list ref]; Benjamin Herrenschmidt
[off-list ref]; Wolfram Sang [off-list ref]; Philipp Zabel
[off-list ref]; openipmi-developer@lists.sourceforge.net;
devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
linux-aspeed@lists.ozlabs.org; linux-kernel@vger.kernel.org;
linux-i2c@vger.kernel.org
Cc: Open Source Submission <redacted>; Thang Q .
Nguyen [off-list ref]; Phong Vo
[off-list ref]; openbmc@lists.ozlabs.org
Subject: [PATCH v3 5/7] i2c: aspeed: Add aspeed_set_slave_busy()

Slave i2c device on AST2500 received a lot of slave irq while it is busy
processing the response. To handle this case, adds and exports
aspeed_set_slave_busy() for controller to temporary stop slave irq while slave
is handling the response, and re-enable them again when the response is ready.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
---
v3:
   + First introduce in v3 [Quan]

  drivers/i2c/busses/i2c-aspeed.c | 20 ++++++++++++++++++++
  1 file changed, 20 insertions(+)

diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index b2e9c8f0ddf7..9926d04831a2 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c

@@ -944,6 +944,26 @@ static int aspeed_i2c_init(struct aspeed_i2c_bus

*bus,
  	return 0;
  }

+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+void aspeed_set_slave_busy(struct i2c_adapter *adap, bool busy) {
+	struct aspeed_i2c_bus *bus = i2c_get_adapdata(adap);
+	unsigned long current_mask, flags;
+
+	spin_lock_irqsave(&bus->lock, flags);
+
+	current_mask = readl(bus->base + ASPEED_I2C_INTR_CTRL_REG);
+	if (busy)
+		current_mask &= ~(ASPEED_I2CD_INTR_RX_DONE |
ASPEED_I2CD_INTR_SLAVE_MATCH);
+	else
+		current_mask |= ASPEED_I2CD_INTR_RX_DONE |
ASPEED_I2CD_INTR_SLAVE_MATCH;
+	writel(current_mask, bus->base + ASPEED_I2C_INTR_CTRL_REG);
+
+	spin_unlock_irqrestore(&bus->lock, flags); }
+EXPORT_SYMBOL_GPL(aspeed_set_slave_busy);
+#endif
+
  static int aspeed_i2c_reset(struct aspeed_i2c_bus *bus)  {
  	struct platform_device *pdev = to_platform_device(bus->dev);
--
2.28.0

Hello,
	The better idea is use disable i2c slave mode.
	Due to if i2c controller running in slave will get slave match, and latch the SCL.
	Until cpu clear interrupt status.
Ryan

Thanks Ryan,

Do you mean to enable/disable slave function as per example code below ?

         /* Turn on slave mode. */
         func_ctrl_reg_val = readl(bus->base + ASPEED_I2C_FUN_CTRL_REG);
         func_ctrl_reg_val |= ASPEED_I2CD_SLAVE_EN;
         writel(func_ctrl_reg_val, bus->base + ASPEED_I2C_FUN_CTRL_REG);

Will try this idea.
- Quan