10.03.2020 18:20, Thierry Reding пишет:
From: Joseph Lo <redacted>
This is the initial patch for Tegra210 EMC frequency scaling. It has the
code to program various aspects of the EMC that are standardized, but it
does not yet include the specific programming sequence needed for clock
scaling.
The driver is designed to support LPDDR4 SDRAM. Devices that use LPDDR4
need to perform training of the RAM before it can be used. Firmware will
perform this training during early boot and pass a table of supported
frequencies to the kernel via device tree.
For the frequencies above 800 MHz, periodic retraining is needed to
compensate for changes in timing. This periodic training will have to be
performed until the frequency drops back to or below 800 MHz.
This driver provides helpers used during this runtime retraining that
will be used by the sequence specific code in a follow-up patch.
Based on work by Peter De Schrijver [off-list ref].
Signed-off-by: Joseph Lo <redacted>
Signed-off-by: Thierry Reding <redacted>
---
Changes in v5:
- major rework and cleanup
...
quoted hunk ↗ jump to hunk
#include "mc.h"
+#define DVFS_FGCG_HIGH_SPEED_THRESHOLD 1000
+#define IOBRICK_DCC_THRESHOLD 2400
+#define DVFS_FGCG_MID_SPEED_THRESHOLD 600
+
+#define EMC_STATUS_UPDATE_TIMEOUT 1000
+
+#define MC_EMEM_ADR_CFG 0x54
+#define MC_EMEM_ARB_CFG 0x90
+#define MC_EMEM_ARB_OUTSTANDING_REQ 0x94
+#define MC_EMEM_ARB_TIMING_RCD 0x98
+#define MC_EMEM_ARB_TIMING_RP 0x9c
+#define MC_EMEM_ARB_TIMING_RC 0xa0
+#define MC_EMEM_ARB_TIMING_RAS 0xa4
+#define MC_EMEM_ARB_TIMING_FAW 0xa8
+#define MC_EMEM_ARB_TIMING_RRD 0xac
+#define MC_EMEM_ARB_TIMING_RAP2PRE 0xb0
+#define MC_EMEM_ARB_TIMING_WAP2PRE 0xb4
+#define MC_EMEM_ARB_TIMING_R2R 0xb8
+#define MC_EMEM_ARB_TIMING_W2W 0xbc
+#define MC_EMEM_ARB_TIMING_R2W 0xc0
+#define MC_EMEM_ARB_TIMING_W2R 0xc4
+#define MC_EMEM_ARB_MISC2 0xc8
+#define MC_EMEM_ARB_DA_TURNS 0xd0
+#define MC_EMEM_ARB_DA_COVERS 0xd4
+#define MC_EMEM_ARB_MISC0 0xd8
+#define MC_EMEM_ARB_MISC1 0xdc
+#define MC_EMEM_ARB_RING1_THROTTLE 0xe0
All these registers are already defined in mc.h, please don't re-define
them.
quoted hunk ↗ jump to hunk
+#define MC_LATENCY_ALLOWANCE_AVPC_0 0x2e4
+#define MC_LATENCY_ALLOWANCE_HC_0 0x310
+#define MC_LATENCY_ALLOWANCE_HC_1 0x314
+#define MC_LATENCY_ALLOWANCE_MPCORE_0 0x320
+#define MC_LATENCY_ALLOWANCE_NVENC_0 0x328
+#define MC_LATENCY_ALLOWANCE_PPCS_0 0x344
+#define MC_LATENCY_ALLOWANCE_PPCS_1 0x348
+#define MC_LATENCY_ALLOWANCE_ISP2_0 0x370
+#define MC_LATENCY_ALLOWANCE_ISP2_1 0x374
+#define MC_LATENCY_ALLOWANCE_XUSB_0 0x37c
+#define MC_LATENCY_ALLOWANCE_XUSB_1 0x380
+#define MC_LATENCY_ALLOWANCE_TSEC_0 0x390
+#define MC_LATENCY_ALLOWANCE_VIC_0 0x394
+#define MC_LATENCY_ALLOWANCE_VI2_0 0x398
+#define MC_LATENCY_ALLOWANCE_GPU_0 0x3ac
+#define MC_LATENCY_ALLOWANCE_SDMMCA_0 0x3b8
+#define MC_LATENCY_ALLOWANCE_SDMMCAA_0 0x3bc
+#define MC_LATENCY_ALLOWANCE_SDMMC_0 0x3c0
+#define MC_LATENCY_ALLOWANCE_SDMMCAB_0 0x3c4
+#define MC_LATENCY_ALLOWANCE_GPU2_0 0x3e8
+#define MC_LATENCY_ALLOWANCE_NVDEC_0 0x3d8
+#define MC_MLL_MPCORER_PTSA_RATE 0x44c
+#define MC_FTOP_PTSA_RATE 0x50c
+#define MC_EMEM_ARB_TIMING_RFCPB 0x6c0
+#define MC_EMEM_ARB_TIMING_CCDMW 0x6c4
+#define MC_EMEM_ARB_REFPB_HP_CTRL 0x6f0
+#define MC_EMEM_ARB_REFPB_BANK_CTRL 0x6f4
+#define MC_PTSA_GRANT_DECREMENT 0x960
+#define MC_EMEM_ARB_DHYST_CTRL 0xbcc
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_0 0xbd0
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_1 0xbd4
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_2 0xbd8
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_3 0xbdc
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_4 0xbe0
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_5 0xbe4
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_6 0xbe8
+#define MC_EMEM_ARB_DHYST_TIMEOUT_UTIL_7 0xbec...
Secondly, looks like it all is unused, hence just remove it.