On 14-08-19, 10:08, Stephen Boyd wrote:

Quoting Vinod Koul (2019-08-14 05:50:00)

quoted

Add the pon and adc nodes found in pm8150b PMIC.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/pm8150b.dtsi | 54 +++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

Squash?

Ok

quoted

diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index c0a678b0f159..846197bd65cd 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi

@@ -2,6 +2,7 @@
 // Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
 // Copyright (c) 2019, Linaro Limited
 
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 

@@ -11,6 +12,59 @@
                reg = <0x2 SPMI_USID>;
                #address-cells = <1>;
                #size-cells = <0>;
+
+               pon@800 {

Maybe pon node name should be 'key' or 'power-on'?

pon stands for power on device. See Documentation/devicetree/bindings/power/reset/qcom,pon.txt

quoted

+                       compatible = "qcom,pm8916-pon";
+                       reg = <0x0800>;
+               };
+
+               adc@3100 {
+                       compatible = "qcom,spmi-adc5";
+                       reg = <0x3100>;
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       #io-channel-cells = <1>;
+                       interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+                       ref-gnd@0 {
+                               reg = <ADC5_REF_GND>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "ref_gnd";
+                       };
+
+                       vref-1p25@1 {
+                               reg = <ADC5_1P25VREF>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "vref_1p25";
+                       };
+
+                       die-temp@6 {
+                               reg = <ADC5_DIE_TEMP>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "die_temp";
+                       };
+
+                       chg-temp@9 {
+                               reg = <ADC5_CHG_TEMP>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "chg_temp";
+                       };
+
+                       smb1390-therm@14 {
+                               reg = <ADC5_AMUX_THM2>;
+                               qcom,hw-settle-time = <200>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "smb1390_therm";
+                       };
+
+                       smb1355-therm@78 {
+                               reg = <ADC5_AMUX_THM2_100K_PU>;
+                               qcom,ratiometric;
+                               qcom,hw-settle-time = <200>;
+                               qcom,pre-scaling = <1 1>;
+                               label = "smb1355_therm";
+                       };

Again, are these board level details? Maybe should be provided here with
status = "disabled" and then added by the boards that use these ADCs.

Sure I will update these

-- 
~Vinod